You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join our community today!
RE: ------>2006 Mustang GT Transformed into 70' Mach 1 "Must see" many pictures<--------
there is a shop that does this with Chargers and Challengers only. but they make there own custom frames. apparently they drive like modern day sportscars. they sell for well over 100,000 tho.
__________________ 2008 Performance White GT/CS - Build Date: 2/15/2008 - Tuned by Brenspeed/C&L Intake/SCT Tuner/Corsa/FRPP Springs/Tokico Shocks/BMR Strut Brace /BMR LCAs/BMR Brackets/Steeda Pan. Bar/FRPP Cam Covers/Bullitt Grille w/ Tri-Bar Pony/8" Shorty Antenna/Hood Struts/CS Stripe Delete/Clear Corners/White Shift Ball w/ Grabber Pony Collar/Sat Radio/S2000 Start Button/Altec Front Plate Mount
RE: ------>2006 Mustang GT Transformed into 70' Mach 1 "Must see" many pictures<--------
You said that this was your first post, then I'd like to welcome you to the forums. I can't wait to see the final product. Please keep us up on everyting with lots of pics. Thanks
RE: ------>2006 Mustang GT Transformed into 70' Mach 1 "Must see" many pictures<----
Hello again, We have posted a few more pictures on the website and also added 2 more new video clips. Sorry these video clips are not edited but I hope they are informative and tell the story. http://nwautocreations.com/photos.html
We have finished the rear tail light panel and trimming of the rear end. Our next obstacle is fitting the fenders and 1/4 panels to the wheelbase of the car. This entails re-installing the motor, trans, and front suspension. We then will lower the car down to our desired ride height to get the final measurements at that point. Right now we don't know whether the width of wheel track will fit or the 1/4 panels maybe widened. This is where we are at today.
Any questions please ask?
I will try to update the pics and videos every other day as we progress.
RE: ------>2006 Mustang GT Transformed into 70' Mach 1 "Must see" many pictures<----
Thanks alot for the post's, I think it's going to be our next shopproject soon as we finish a gt500 rebody. I love the idea!! great web site you guy's have!!
__________________
07 mustang GT premium auto torch red CAI 93 race tune UDP'S 4.10 gears CMCV delete plates Painted 12 inch stripes Window Louver's painted mirror's pypes violator's ab GT500 front spliter
RE: ------>2006 Mustang GT Transformed into 70' Mach 1 "Must see" many pictures<----
Hello again, we just uploaded 3 more new videos to the website http://www.nwautocreations.com/photos/
which shows last weeks progress. (Finishing the tailight panel area, fitting trunk lid,adjusting all wheel openings to fit center of wheels, temporarily installed engine transmission and suspension to check ride height, purchased BMW hood and hinge setup for modification of the Mach1 hood).
We have found once the car was on the ground that the front wheel width track is narrower than the rear. Therefore, we are going to *wide body* the rear a inch and a half on each side in a very subtle way, as opposed to fender flares, which we don't really care for.
This week, we hope to accomplish all or some of the following;
- Final install of front cowl panel
- All wheel wells welded,finished and in place
- New doors installed and fitted
- Rear inner fenders installed
Well thanks everyone for the nice comments and we are going to try and do new video and picture installments every day
RE: ------>2006 Mustang GT Transformed into 70' Mach 1 "Must see" many pictures<----
Quote:
ORIGINAL: NWAutoCreations
Hello again, we just uploaded 3 more new videos to the website http://www.nwautocreations.com/photos/
which shows last weeks progress. (Finishing the tailight panel area, fitting trunk lid,adjusting all wheel openings to fit center of wheels, temporarily installed engine transmission and suspension to check ride height, purchased BMW hood and hinge setup for modification of the Mach1 hood).
We have found once the car was on the ground that the front wheel width track is narrower than the rear. Therefore, we are going to *wide body* the rear a inch and a half on each side in a very subtle way, as opposed to fender flares, which we don't really care for.
This week, we hope to accomplish all or some of the following;
- Final install of front cowl panel
- All wheel wells welded,finished and in place
- New doors installed and fitted
- Rear inner fenders installed
Well thanks everyone for the nice comments and we are going to try and do new video and picture installments every day
Did you consider narrowing the rear-end?
__________________
Mustang sold, 2007 Dodge Magnum R/T 5.7 Hemi
RE: ------>2006 Mustang GT Transformed into 70' Mach 1 "Must see" many pictures<----
Cool stuff! Not sure if theres a point to it, except personal satisfaction. 99% of the world will see a beater when they see an old body, no matter whats underneath or where it came from, only that other 1% will see a cool mustang or a cool restoration. But yeah, I like the challenge of it all.
This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company
RE: ------>2006 Mustang GT Transformed into 70' Mach 1 "Must see" many pictures<--------
