QTP Electric Cut Out Sale
#1
QTP Electric Cut Out Sale
This week we are featuring QTP electric cutouts on special. For those of you not familiar with the product, electric cutouts allow you bypass the exhaust system for increased performance and noise levels. This can be done right from inside the car in just a few seconds. You can open the cutout completely or just partially open it to suit your needs.
A basic toggle switch is included or you can use the optional digital controller.
The digital controller
Features:
[ul][*][align=left]Calibrates each motor independently and synchronizes their position[/align][/ul]
[ul][*]Automatic close at power up[/ul]
[ul][*]Digital status displays shows butterfly position[/ul]
[ul][*]Manual pushbutton operation for open, close or partial open[/ul]
[ul][*]User configurable partial open position[/ul]
[ul][*]2 Memory preset partial open settings[/ul]
[ul][*]Short circuit protection on motor drive electronics[/ul]
[ul][*]Fault detection and reporting[/ul]
[ul][*]Automatic open or close by grounding or not grounding the trigger wire[/ul]
[ul][*]LED butterfly position status
0-100 0=Closed and 100=Wide Open[/ul]
All single 2 1/4 - 3" electric cutouts are 189.00 each
All dual 2 1/4 - 3" electric cutouts are 375.99 for the pair
You can add the optional digital controller for 100.00. It can control one or two cutouts.
A basic toggle switch is included or you can use the optional digital controller.
The digital controller
Features:
[ul][*][align=left]Calibrates each motor independently and synchronizes their position[/align][/ul]
[ul][*]Automatic close at power up[/ul]
[ul][*]Digital status displays shows butterfly position[/ul]
[ul][*]Manual pushbutton operation for open, close or partial open[/ul]
[ul][*]User configurable partial open position[/ul]
[ul][*]2 Memory preset partial open settings[/ul]
[ul][*]Short circuit protection on motor drive electronics[/ul]
[ul][*]Fault detection and reporting[/ul]
[ul][*]Automatic open or close by grounding or not grounding the trigger wire[/ul]
[ul][*]LED butterfly position status
0-100 0=Closed and 100=Wide Open[/ul]
All single 2 1/4 - 3" electric cutouts are 189.00 each
All dual 2 1/4 - 3" electric cutouts are 375.99 for the pair
You can add the optional digital controller for 100.00. It can control one or two cutouts.
#3
RE: QTP Electric Cut Out Sale
Sorry but we don't have sound clips. Your sound is going to vary depending on where you place them in the exhaust. Most people put them right after their headers and before the cats (if you have them). That basically makes the car unmuffled when you have the cutouts fully open.
The cutouts are universal and needed to be welded in. We would estimate about an hour labour to weld them in and then you need to run the wiring inside the car and to keyed power, ground etc. Not a hard install but if you can't weld, you will need to get a muffler shop to do it for you.
The cutouts are universal and needed to be welded in. We would estimate about an hour labour to weld them in and then you need to run the wiring inside the car and to keyed power, ground etc. Not a hard install but if you can't weld, you will need to get a muffler shop to do it for you.
#4
RE: QTP Electric Cut Out Sale
ORIGINAL: Fast Toys
Sorry but we don't have sound clips. Your sound is going to vary depending on where you place them in the exhaust. Most people put them right after their headers and before the cats (if you have them). That basically makes the car unmuffled when you have the cutouts fully open.
The cutouts are universal and needed to be welded in. We would estimate about an hour labour to weld them in and then you need to run the wiring inside the car and to keyed power, ground etc. Not a hard install but if you can't weld, you will need to get a muffler shop to do it for you.
Sorry but we don't have sound clips. Your sound is going to vary depending on where you place them in the exhaust. Most people put them right after their headers and before the cats (if you have them). That basically makes the car unmuffled when you have the cutouts fully open.
The cutouts are universal and needed to be welded in. We would estimate about an hour labour to weld them in and then you need to run the wiring inside the car and to keyed power, ground etc. Not a hard install but if you can't weld, you will need to get a muffler shop to do it for you.
#7
RE: QTP Electric Cut Out Sale
Sale ends next Friday. They are a universal weld in design. As long as you have remove to cut out a section of exhaust to weld these in, you can install them. Just take a peek under yourvehicle anddetermine if youhave a good spot that theycan be installed.
They are available in many different sizes to match the diameter of the exhaust tubing you have on your vehicle.
They are available in many different sizes to match the diameter of the exhaust tubing you have on your vehicle.
#10
RE: QTP Electric Cut Out Sale
ORIGINAL: 05BlueGT
Wasn't you working on some exhaust tips?
Wasn't you working on some exhaust tips?
Regular pricing on the QTP cutouts are shown on our web site as well.
Thanks