REAR END NOISE!
09-29-2011, 05:04 PM
#11
OK guys i've been hearing a humming noise that seems to be coming from rear end when i reach speed from 60mph and up and pressure on gas pedal. As soon as i let go of gas noise is gone! dealer has said that the rear diff is fine and noise is coming from exhaust resonance. is this possible?
Are you still hearing the humming noise? If so, Please PM me with your VIN, contact information, mileage, & servicing dealer name/state and I will assist. Thanks!
~Natasha
09-30-2011, 04:08 PM
#12
1st Gear Member
Thread Starter
Join Date: Sep 2011
Location: Canada
Posts: 61
i dont think theres much you can do to help... dealers have looked at the car and have told me that its a mix of muffler and drive train resonance. Told me there is no abnormal noise coming from rear diff. They refuse to open up diff for no reason
03-10-2014, 07:19 PM
#13
Join Date: Mar 2014
Location: IN
Posts: 2
i have had two 08 bullitts. i have had this problem in both. i can hear the whine from around 30-80mph. after eighty i cant hear anything. i always thought it might be the exhaust. but,, now im not sure. after seeing this:
Year: 2010
Model: Mustang
Model: 09-20-4
TSB 09-20-4 AXLE WHINE Publication Date: September 28, 2009
FORD:
2005-2010 Mustang
This article supersedes TSBs 8-21-6 to update the vehicle model years.
ISSUE:
Some 2005-2010 Mustang vehicles may exhibit excessive axle whine noise.
ACTION:
Follow the Service Procedure steps to correct the condition.
SERVICE PROCEDURE
This condition may be corrected by installing tuned dampers on the rear axle assembly, if not already installed.
1. Check the rear axle assembly for the presence of tuned dampers. (Figures 1-2) Figure 1 - Article 09-20-4
Figure 2 - Article 09-20-4
2. If not present, then install tuned dampers. Refer to the installation instruction sheet included in the damper kit.
NOTE:
NO DRILLING IS REQUIRED IF DAMPER MOUNTING HOLES ARE PRESENT. VEHICLES BUILT AFTER 11/15/2004 ALREADY HAVE THE REQUIRED DAMPER MOUNTING HOLES.
3. If whine noise persists, then continue with normal diagnostics per Workshop Manual, Section 205-00.
PART NUMBER
PART NAME
5R3Z-3C246-A
Damper Kit
WARRANTY STATUS:
Eligible Under Provisions Of New Vehicle Limited Warranty Coverage IMPORTANT: Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part.
OPERATION
DESCRIPTION
TIME
092004A
2005-2010 Mustang: Install Axle Damper Kit Includes Time To Drill Holes If Necessary (Do Not Use With Any Other Labor Operations)
0.6 Hr.
DEALER CODING
BASIC PART NO.
CONDITION CODE
4010
d9
i still have thw noise. it sucks. do you??
Year: 2010
Model: Mustang
Model: 09-20-4
TSB 09-20-4 AXLE WHINE Publication Date: September 28, 2009
FORD:
2005-2010 Mustang
This article supersedes TSBs 8-21-6 to update the vehicle model years.
ISSUE:
Some 2005-2010 Mustang vehicles may exhibit excessive axle whine noise.
ACTION:
Follow the Service Procedure steps to correct the condition.
SERVICE PROCEDURE
This condition may be corrected by installing tuned dampers on the rear axle assembly, if not already installed.
1. Check the rear axle assembly for the presence of tuned dampers. (Figures 1-2) Figure 1 - Article 09-20-4
Figure 2 - Article 09-20-4
2. If not present, then install tuned dampers. Refer to the installation instruction sheet included in the damper kit.
NOTE:
NO DRILLING IS REQUIRED IF DAMPER MOUNTING HOLES ARE PRESENT. VEHICLES BUILT AFTER 11/15/2004 ALREADY HAVE THE REQUIRED DAMPER MOUNTING HOLES.
3. If whine noise persists, then continue with normal diagnostics per Workshop Manual, Section 205-00.
PART NUMBER
PART NAME
5R3Z-3C246-A
Damper Kit
WARRANTY STATUS:
Eligible Under Provisions Of New Vehicle Limited Warranty Coverage IMPORTANT: Warranty coverage limits/policies are not altered by a TSB. Warranty coverage limits are determined by the identified causal part.
OPERATION
DESCRIPTION
TIME
092004A
2005-2010 Mustang: Install Axle Damper Kit Includes Time To Drill Holes If Necessary (Do Not Use With Any Other Labor Operations)
0.6 Hr.
DEALER CODING
BASIC PART NO.
CONDITION CODE
4010
d9
i still have thw noise. it sucks. do you??
Thread
Thread Starter
Forum
Replies
Last Post
musnicki
Classic Mustang General Discussion
8
09-23-2015 07:11 AM
Dragonus18
4.6L (1996-2004 Modular) Mustang
8
09-09-2015 01:21 AM
