Banshee Shaker and MAF
01-27-2004, 01:41 AM
#1
1st Gear Member
Thread Starter
Join Date: Jan 2004
Location: United States
Posts: 80
Banshee Shaker and MAF
Ok..I think I know what I want but I'm not sure if it can be done. I want to put the Banshee Ram Jet hood and shaker on my 03 GT coupe with a C&L 85mm MAF w/TrueFlow inlet pipe. I think I'm gonna put the 75mm Accufab TB and C&L Plenum on there too. Think I'm gonna do it all at once. My question is can I use the Banshee shaker with the MAF from C&L? Is 85mm over kill...I mean is it any better than 75mm since the TB and plenum are just 75mm? HELP....I've read every article I could find and apparently I either A) Arn't looking in the right place or B) what I'm reading is going over my head. I'm real new to these mods. Please answer using small word and as little alphebet soup as possible. <IMG src=smileys/smiley1.gif border="0">
01-27-2004, 02:13 AM
#2
2nd Gear Member
Join Date: Jan 2004
Location: United States
Posts: 478
Banshee Shaker and MAF
Better hold off until you read some more opinions. First I believe the 03 has the 80mm MAF same as 02, most say that big enough for most applications. Second a 75 MM TB is prob overkill too and most will tell you it will hurt performance if you exceed 70 MM unless you add a supercharger. I would say change the intake and TB then go work on the exhaust end.
01-27-2004, 02:24 AM
#3
1st Gear Member
Thread Starter
Join Date: Jan 2004
Location: United States
Posts: 80
Banshee Shaker and MAF
I'm planning on getting a supercharger in a month or two. But I want to put all the cheaperstuff first. I didn't know about that the 03 had an 80mm...good thing to know.Should I just put agood old 80mm K&N on threre then?I REALLY want the Shaker. Should I even do the MAF?Is it possible (and even a good idea) to use the Banshee shaker with the MAF from C&L (I'm still leaning towards the 85mm w/TrueFlow inlet pipe)?
01-27-2004, 02:55 AM
#4
6th Gear Member
Join Date: Jan 2004
Location: United States
Posts: 12,575
Banshee Shaker and MAF
Is it gonna be a bitch at all to run both the shaker and the S/C? I saw an artical of the first guy (according to MM+FF) to put a blower on a mach one, and he had to get alot of custom fab stuff.
01-28-2004, 01:02 AM
#5
I ♥ Acer
Join Date: Jan 2004
Location: Reading, Pa.
Posts: 2,617
Banshee Shaker and MAF
Originally Posted by RJM02GTDrag
Better hold off until you read some more opinions. First I believe the 03 has the 80mm MAF same as 02, most say that big enough for most applications. Second a 75 MM TB is prob overkill too and most will tell you it will hurt performance if you exceed 70 MM unless you add a supercharger. I would say change the intake and TB then go work on the exhaust end.
'03 Mustang GT has a 85mm meter.</P>
He's thinking of the 75mm throttle body because C&L, through dyno testing found out that you get the most gains using a 75mm TB with their new plenum. Although they tested it with the BBK.</P>
01-28-2004, 01:11 AM
#6
I ♥ Acer
Join Date: Jan 2004
Location: Reading, Pa.
Posts: 2,617
Banshee Shaker and MAF
Originally Posted by Marc_03GT
Ok..I think I know what I want but I'm not sure if it can be done. I want to put the Banshee Ram Jet hood and shaker on my 03 GT coupe with a C&L 85mm MAF w/TrueFlow inlet pipe. I think I'm gonna put the 75mm Accufab TB and C&L Plenum on there too. Think I'm gonna do it all at once. My question is can I use the Banshee shaker with the MAF from C&L? Is 85mm over kill...I mean is it any better than 75mm since the TB and plenum are just 75mm? HELP....I've read every article I could find and apparently I either A) Arn't looking in the right place or B) what I'm reading is going over my head. I'm real new to these mods. Please answer using small word and as little alphebet soup as possible. <IMG src=smileys/smiley1.gif border="0">
As I told you in your earlier posts I do not believe you can do both the shaker and C&L MAF. Guys, help me out with this. Is this correct???</P>
</P>
Thread
Thread Starter
Forum
Replies
Last Post
jwog666
Pipes, Boost & Juice
11
12-27-2021 08:09 PM
JoshyGT
S550 2015-2023 Mustang
16
09-19-2017 08:52 PM