People who have a Procharger P1-SC...LOOK HERE PLEASE
#2
RE: People who have a Procharger P1-SC...LOOK HERE PLEASE
Its definitely a good entry level blower. If you are planning on a built bottom end and big power down the road, then get something bigger. The p-1sc will take you to about 500rwhp give or take depending on mods of course. But the "safe" limit on the stock bottom end is around 400rwhp, so it you never plan on doing the bottom end its the perfect choice. All their kits come intercooled for a few hundred more than other entry level blowers that come non-intercooled.
#3
RE: People who have a Procharger P1-SC...LOOK HERE PLEASE
The Procharger P1SC Stage II package is a very well balenced package. Its more then capable of taking you from 380rwhp to a little over 500rwhp. Very street friendly, very efficent at low psi. 50 state legal. All around good system. And 500rwhp is more then enough with the right supporting mods to bring you into the 11s.
Depending on your setup, max boost with an 8rib pulley is around 12psi to 14psi(maybe). The most power output I've seen from a P1 was 540rwhp @ 13psi. The thing was just sick.
If you feel the need to exceed 600rwhp, then the D1 will be your choice. I think they go up to 20psi. They are the same size as a P1, just with different impellars. You don't need an 8-rib setup if you wanna run max boost with them.
Then if you have deep pockets with just the insane need for power..... The F-1A will be your way to go. They max out at some ridculous amount of boost and run on a COG belt. They will also make your ear drums bleed at an idle from the jet powered whistle they have.
Depending on your setup, max boost with an 8rib pulley is around 12psi to 14psi(maybe). The most power output I've seen from a P1 was 540rwhp @ 13psi. The thing was just sick.
If you feel the need to exceed 600rwhp, then the D1 will be your choice. I think they go up to 20psi. They are the same size as a P1, just with different impellars. You don't need an 8-rib setup if you wanna run max boost with them.
Then if you have deep pockets with just the insane need for power..... The F-1A will be your way to go. They max out at some ridculous amount of boost and run on a COG belt. They will also make your ear drums bleed at an idle from the jet powered whistle they have.
#4
RE: People who have a Procharger P1-SC...LOOK HERE PLEASE
ORIGINAL: mylongvictor
The Procharger P1SC Stage II package is a very well balenced package. Its more then capable of taking you from 380rwhp to a little over 500rwhp. Very street friendly, very efficent at low psi. 50 state legal. All around good system. And 500rwhp is more then enough with the right supporting mods to bring you into the 11s.
Depending on your setup, max boost with an 8rib pulley is around 12psi to 14psi(maybe). The most power output I've seen from a P1 was 540rwhp @ 13psi. The thing was just sick.
If you feel the need to exceed 600rwhp, then the D1 will be your choice. I think they go up to 20psi. They are the same size as a P1, just with different impellars. You don't need an 8-rib setup if you wanna run max boost with them.
Then if you have deep pockets with just the insane need for power..... The F-1A will be your way to go. They max out at some ridculous amount of boost and run on a COG belt. They will also make your ear drums bleed at an idle from the jet powered whistle they have.
The Procharger P1SC Stage II package is a very well balenced package. Its more then capable of taking you from 380rwhp to a little over 500rwhp. Very street friendly, very efficent at low psi. 50 state legal. All around good system. And 500rwhp is more then enough with the right supporting mods to bring you into the 11s.
Depending on your setup, max boost with an 8rib pulley is around 12psi to 14psi(maybe). The most power output I've seen from a P1 was 540rwhp @ 13psi. The thing was just sick.
If you feel the need to exceed 600rwhp, then the D1 will be your choice. I think they go up to 20psi. They are the same size as a P1, just with different impellars. You don't need an 8-rib setup if you wanna run max boost with them.
Then if you have deep pockets with just the insane need for power..... The F-1A will be your way to go. They max out at some ridculous amount of boost and run on a COG belt. They will also make your ear drums bleed at an idle from the jet powered whistle they have.
I mean for almost 700 I can find a COMPLETE NITROUS kit
(SRY FOR HIJACKING THREAD OP)
Good luck with ur BLOWER!!!
#5
RE: People who have a Procharger P1-SC...LOOK HERE PLEASE
I believe Contentsunderpressure has a p1 with a 3.2 pulley with no 8-rib conversion. If that don't slip then I doubt the D-1 would. But then agian. Listen to the Procharger Experts from ATI!
#6
RE: People who have a Procharger P1-SC...LOOK HERE PLEASE
I know the P-1sc isn't supposed to slip until smaller than 3.2. But If I had a D-1sc running high boost, I would definitely pick up a Reichard racing pulley and never have to worry about slippage.
BTW the F-1A comes with an 8-rib pulley that will actually work with your stock 6-rib pulley system until you upgrade. I don't know how much pressure you can run with the F-1A on a 6-rib belt without slip though.
BTW the F-1A comes with an 8-rib pulley that will actually work with your stock 6-rib pulley system until you upgrade. I don't know how much pressure you can run with the F-1A on a 6-rib belt without slip though.
#7
RE: People who have a Procharger P1-SC...LOOK HERE PLEASE
ORIGINAL: tbirdscwd
I know the P-1sc isn't supposed to slip until smaller than 3.2. But If I had a D-1sc running high boost, I would definitely pick up a Reichard racing pulley and never have to worry about slippage.
BTW the F-1A comes with an 8-rib pulley that will actually work with your stock 6-rib pulley system until you upgrade. I don't know how much pressure you can run with the F-1A on a 6-rib belt without slip though.
I know the P-1sc isn't supposed to slip until smaller than 3.2. But If I had a D-1sc running high boost, I would definitely pick up a Reichard racing pulley and never have to worry about slippage.
BTW the F-1A comes with an 8-rib pulley that will actually work with your stock 6-rib pulley system until you upgrade. I don't know how much pressure you can run with the F-1A on a 6-rib belt without slip though.
#8
RE: People who have a Procharger P1-SC...LOOK HERE PLEASE
ORIGINAL: mylongvictor
P-1SC will usually over spin at around 2.8 w/ an Rib. At that point the P1 is just screaming for mercy. A 3.0 w/ AFM Powerpipe will net my car at around 11psi. Maybe.
ORIGINAL: tbirdscwd
I know the P-1sc isn't supposed to slip until smaller than 3.2. But If I had a D-1sc running high boost, I would definitely pick up a Reichard racing pulley and never have to worry about slippage.
BTW the F-1A comes with an 8-rib pulley that will actually work with your stock 6-rib pulley system until you upgrade. I don't know how much pressure you can run with the F-1A on a 6-rib belt without slip though.
I know the P-1sc isn't supposed to slip until smaller than 3.2. But If I had a D-1sc running high boost, I would definitely pick up a Reichard racing pulley and never have to worry about slippage.
BTW the F-1A comes with an 8-rib pulley that will actually work with your stock 6-rib pulley system until you upgrade. I don't know how much pressure you can run with the F-1A on a 6-rib belt without slip though.
BTW what heads/cams are you running? 3.0 should get you a couple more psi than that unless you have like stage 3 heads/cams, LTs, and an aftermaket intake.
#9
RE: People who have a Procharger P1-SC...LOOK HERE PLEASE
ORIGINAL: tbirdscwd
what rib?
BTW what heads/cams are you running? 3.0 should get you a couple more psi than that unless you have like stage 3 heads/cams, LTs, and an aftermaket intake.
ORIGINAL: mylongvictor
P-1SC will usually over spin at around 2.8 w/ an Rib. At that point the P1 is just screaming for mercy. A 3.0 w/ AFM Powerpipe will net my car at around 11psi. Maybe.
ORIGINAL: tbirdscwd
I know the P-1sc isn't supposed to slip until smaller than 3.2. But If I had a D-1sc running high boost, I would definitely pick up a Reichard racing pulley and never have to worry about slippage.
BTW the F-1A comes with an 8-rib pulley that will actually work with your stock 6-rib pulley system until you upgrade. I don't know how much pressure you can run with the F-1A on a 6-rib belt without slip though.
I know the P-1sc isn't supposed to slip until smaller than 3.2. But If I had a D-1sc running high boost, I would definitely pick up a Reichard racing pulley and never have to worry about slippage.
BTW the F-1A comes with an 8-rib pulley that will actually work with your stock 6-rib pulley system until you upgrade. I don't know how much pressure you can run with the F-1A on a 6-rib belt without slip though.
BTW what heads/cams are you running? 3.0 should get you a couple more psi than that unless you have like stage 3 heads/cams, LTs, and an aftermaket intake.
#10
RE: People who have a Procharger P1-SC...LOOK HERE PLEASE
What pulley were you running that gave you 477rwhp @8psi? Just curious cause my car was pushing 11psi on stock heads/cams stock intake tube with a 3.4" at 400rwhp. I'm getting it dynoed tomorrow with the new motor with blower cams and the same pulley. We'll see how much the pressure reading drops. I'd be really happy with 450rwhp on the 3.4 incher. I just got a power pipe but haven't installed it yet.