Soaring

Since there is an interest in having a thread on top to show off our engine bays, I think we should make some basic rules. 1. Try to get the best shot of your engine bay as you can. 2. List what you have. In other words which engine, which uprades if any etc. We will pin this to the top so that everyone on here can see pics of our engine bays and ask the owners questions about how they achieved the performance and look that they did. This is just for engine bays. We already have a pin for the whole cars.
Here's mine to start.
1965 289 C code basically stock with a shroud, Monte Carlo bar, Export brace and radiator overflow tank.

4reboy

I'll contribute. I posted these in the last engine bay thread.

Bay - stripped and sandblasted, etching primer, laquer primer, then a semi-flat black. (sprayed with HVLP gun, not a rattle can)
Engine - rebuilt 351w (original to car), bored .04 over. Edelbrock performer intake with edelbrock 650 cfm carb (electric choke), plus a high volume aluminum water pump. I put an export brace on, and eventually a monte carlo bar. Also have a stock style 3-row radiator rather than the original 2-row. Oh I aslo have a 100 amp alternator. EDIT, forgot, also have MSD 8.5mm spark plug wires, new cap and rotor, and pertronix ignition (now blown )

Aussie66Fastback

cool idea. here's mine
302, mild cam, p and p 351 heads, holley 600 vac sec, roller rockers, tri-y to twin 2 1/4 with H, electronic ignition. Since the photo was taken, I have put std rocker covers back on, hipo 289 aircleaner to make it look like a factory motor to the uneducated

[IMG]local://upfiles/48146/587D639319E04B28875563983C44B76D.jpg[/IMG]

ndnboy

Here is mine:

Stock 289, 4V, Electronic Ignition, chrome Monte Carlo Bar, chrome Air/valve cover dress up kit, dual master cylinder, 3 row radiator

[IMG]local://upfiles/62235/4E264656262848628B589D01D7F793C7.jpg[/IMG]

bluovalguy

Some dirt, alittle rust, MSD Dizzy, MSD Wires, Mallory Promaster Coil, Edelbrock 600 cfm, Edelbrock Performer RPM manifold, Hooker full length headers, a couple randomly placed zip strips, and a air cleaner decal that is pealing off

dodgestang

mustanglover66

I'll play along. MSD 6AL, MSD Dist. with 9mm ford raceing wires on a worn out 302 with holley 600 4V and edelbrock Performer intake. Of course all of which about to be pulled out soon.

[IMG]local://upfiles/33399/8E566A15794A4C2B93C9B6AC8A86A635.jpg[/IMG]

[IMG]local://upfiles/33399/559E3A2F96B84AF1AB7DE0AB3DA2E8D1.jpg[/IMG]

68EFIvert

302 bord 30 over, E303 cam, forged pistons with balanced rotating assembly, Ford aluminum heads, C&L MAF and inlet, 24 lb injectors, 1.7 rr, Professional Products Intake, March pulleys and brackets, Northern Radiator and an export brace I made from flat stock and hex aluminum rod. Oh and lots of bondo dust. I'll take care of cleaning after it is painted.

LCC

Here's my old 351C, not in it right now


New 351W

66JameStang

Car- 66 Mustang- Project- 66JameStang and JMD,

Well I want to give you the overall picture of my engine and bay even though it is not complete yet.
The car started out with an inline 6 and was driven for awhile before my brakes went out. I have since replaced it with a monster. The engine bay took time:

Here is a picture of the engine and bay when I baught the car-



It was a rough starting point but it really helped. From here we of coarse started by removing the engine and proceding with clean up. Before really starting I pulled the wiring harness out of the vehicle because I wanted a clean spray through out the car and especailly the bay. After the harness was removed I started scuffing but realized it was going to be a large task. We decided to use aircraft remover to strip the paint and it worked really well.






At this point we cleaned it up a bit more and laid down the primer..





I don't have a picture but we purchased bed liner and laid it down in most of the engine compartment and added texture. The bed liner was black but the paint laid downnice on top of it. We used single stage dupontpaint.





The engine that was built for this car was built from the ground up.
Engine- 351 Windsor- Tore down- came from 1970 LTD
Exhaust manifold- Victor Jr
Intake Manifold- Edlebrock Air Gap
Forged Crank and pistons
H-Beam rods
Stroked to 408
Cam-
Carburater- Demon
Roller Lifters
Distributer- Mallory



Painted the block silver the same silver as the bay.


The oil pan has been changed because it was too small for new internals




It is still not finished yet but it is coming along the wires are not where They are gonna be yet and some things still needto be moved around. I will post more as we finish it.