289 cam question !! - Page 2 - MustangForums.com


Go Back   MustangForums.com > Ford Mustang Tech > Classic Mustangs (Tech)
Search


Classic Mustangs (Tech) Technical discussions about the Mustangs of yester-year.

289 cam question !!

Reply
 
 
 
Thread Tools Search this Thread
Old 07-04-2014, 02:40 PM   #11
mhubert89
1st Gear Member
 
Join Date: Nov 2012
Vehicle: Ford Mustang Fastback 68
Location: Canada
Posts: 98
Default

Quote:
Originally Posted by barnett468 View Post
ok good. i would run the xe262h as delivered, in your case then.
COMP Cams Camshaft Small Kit Xtreme Energy XE262H Hydraulic Flat Tappet 1300-5600 RPM 289/302

Do you think its a good small kit.. From cjponyparts comme with ;
Camshaft, lifter , timing chain set and lub for 225$ !?
mhubert89 is offline   Reply With Quote
Old 07-04-2014, 04:20 PM   #12
barnett468
4th Gear Member
 
Join Date: Nov 2013
Vehicle: 1965 shelby
Location: arizona
Posts: 1,300
Default

hello;

the cam and springs are fine but you can not run comp lifters, they are not all good. buy crane high rev lifters or howards etc..
barnett468 is offline   Reply With Quote
Old 07-04-2014, 05:31 PM   #13
mhubert89
1st Gear Member
 
Join Date: Nov 2012
Vehicle: Ford Mustang Fastback 68
Location: Canada
Posts: 98
Default

Quote:
Originally Posted by barnett468 View Post
hello;

the cam and springs are fine but you can not run comp lifters, they are not all good. buy crane high rev lifters or howards etc..
Oki i will only buy the cam from that kit !! Thks
mhubert89 is offline   Reply With Quote
Old 07-04-2014, 05:53 PM   #14
mhubert89
1st Gear Member
 
Join Date: Nov 2012
Vehicle: Ford Mustang Fastback 68
Location: Canada
Posts: 98
Default

I need also a flywheel and a clutch ( maybe a stage 2) .. Do you have any suggestion about this 2 parts sir ?!
mhubert89 is offline   Reply With Quote
Old 07-04-2014, 09:05 PM   #15
barnett468
4th Gear Member
 
Join Date: Nov 2013
Vehicle: 1965 shelby
Location: arizona
Posts: 1,300
Default

Quote:
Originally Posted by mhubert89 View Post
I need also a flywheel and a clutch ( maybe a stage 2) .. Do you have any suggestion about this 2 parts sir ?!
hi;

yes, a 10 1/2" mcleod 1650 lb 3 finger pressure plate from summit racing and a series 100 disc if you drive casually and a series 500 dual friction if you flog it. small diameter 10 spline shaft if your trans is stock.



.

Last edited by barnett468; 07-04-2014 at 09:07 PM.
barnett468 is offline   Reply With Quote
Old 07-06-2014, 03:48 PM   #16
mhubert89
1st Gear Member
 
Join Date: Nov 2012
Vehicle: Ford Mustang Fastback 68
Location: Canada
Posts: 98
Default

Never buy from summit i will go to check to find this parts ! Thanks again !!
mhubert89 is offline   Reply With Quote
Old 07-07-2014, 04:32 PM   #17
groho
4th Gear Member
 
groho's Avatar
 
Join Date: Oct 2005
Posts: 1,163
Default

I've been buying summit for years. They're probably your best bet on availability and pricing. I'm lucky, they're right up the road, order on a tues morning, on my doorstep the next afternoon.
groho is offline   Reply With Quote
Old 08-18-2014, 10:35 AM   #18
mhubert89
1st Gear Member
 
Join Date: Nov 2012
Vehicle: Ford Mustang Fastback 68
Location: Canada
Posts: 98
Default

Quote:
Originally Posted by barnett468 View Post
hello;

the cam and springs are fine but you can not run comp lifters, they are not all good. buy crane high rev lifters or howards etc..
Can you told me wich one that will be better for my engine to buy ! The lifters names ..

thanks
appreciate
mhubert89 is offline   Reply With Quote

 
 
Reply

Similar Threads
Thread Thread Starter Forum Replies Last Post
How to get good HP out of a 4.6 without spending big bucks. Luke9222 4.6L General Discussion 19 10-22-2015 11:55 PM
New 5.0 carb build bogs at hit of throttle Daddys Girls GTs 5.0L (1979-1995) Mustang 3 09-14-2015 08:46 PM
built help EASTIDEE123 5.0L (1979-1995) Mustang 14 09-14-2015 03:52 PM
Cam and rear end gear questions Ryan Fitzpatrick New Member Area 3 09-14-2015 02:21 AM
ford 289 ryland Mustang News, Concepts, Rumors & Discussion 0 09-13-2015 12:35 PM


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump

 

All times are GMT -5. The time now is 09:36 AM.



This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company