OnDemand 5 - Repair help for you.

Reply Subscribe

Thread Tools

Search this Thread

02-17-2009, 08:34 PM

#31

Juno

2nd Gear Member

Thread Starter

Join Date: Nov 2008

Location: NJ

Posts: 236

Sorry for waiting but i had some hardware problems...

Quote:

Originally Posted by mustang35

I'll take the wiring diagram that you have. Thanks for the help. I'll let you know what I find out.

http://img338.imageshack.us/img338/2...owanie1xf3.jpg

Quote:

Originally Posted by 1Low5.0

1989 Mustang LX Convertible
Replacing both existing OEM Sun Visors with 2 new replacements. Any information would be helpful.

Thanks much,
1Low5.0 (oh)

Nothing about that

Quote:

Originally Posted by yeewiz

Hey Juno, you were such a fantastic help the last time on programming my remotes, I'm BAAAAACKKKK. Do you have a diagram for a 98 stang V6 3.8 A/C vacuum lines, or the vacuum distribution block? Anything on vaccuum lines in the engine compartment if the above 2 topics come up short. Dude, once again, you are the MAN! Thanks!

http://img338.imageshack.us/img338/6...aganie1gp6.jpg

Is that the thing that you are looking for?

Quote:

Originally Posted by jwalker3472

I have replaced the calipers on my 02 coupe. The problem is I cannot get the springs to the e-brake on to the caliper any suggestions?

I just give you anything about replacing the calipers, maybe you will find out what you did wrong ;p

http://img11.imageshack.us/img11/7258/hamulce2rd8.jpg

And FIG-s:
http://img11.imageshack.us/img11/6567/fig1ur7.jpg
http://img11.imageshack.us/img11/3400/fig2ty2.jpg
http://img24.imageshack.us/img24/633/fig3wd9.jpg
http://img510.imageshack.us/img510/7015/fig4tu3.jpg
http://img18.imageshack.us/img18/6548/fig5hd8.jpg

Quote:

Originally Posted by JRS98SVTCOBRA

HI JUNO DO YOU HAVE INFO OFR REPLACING ROD BEARINGS ON MY 98 COBRA VERT TRYING TO FIGURE OUT HOW TO GET THE OIL PAN OUT WITH OUT PULLING THE ENGINE OUT

What engine do you have?

02-17-2009, 09:26 PM

#32

JRS98SVTCOBRA

Join Date: Feb 2009

Location: FLORIDA

Posts: 23

What engine do you have?[/QUOTE]

4.6 dohc cobra

02-17-2009, 09:35 PM

#33

yeewiz

Join Date: Nov 2008

Location: Concord, CA

Posts: 43

Hi Juno, re the vacuum line diagram, the one you attached doesn't look right. In the vacuum distribution block on my 'stang, there is one port labeled "A/C". I am told this should connect to something that T's into an A/C cannister. I'm trying to reconstruct this A/C vacuum line. I will take a picture tomorrow if you don't find anything. Thanks again!

02-17-2009, 10:33 PM

#34

Juno

2nd Gear Member

Thread Starter

Join Date: Nov 2008

Location: NJ

Posts: 236

Quote:

Originally Posted by JRS98SVTCOBRA

4.6 dohc cobra

http://img19.imageshack.us/img19/5598/capture1ik0.jpg
Thats it about that

Quote:

Originally Posted by yeewiz

You got an 1998 Mustang 3.8 V6 Right?
Its nothing more about this

Just take a PIC

02-17-2009, 10:55 PM

#35

yeewiz

Join Date: Nov 2008

Location: Concord, CA

Posts: 43

yeah, 98 3.8 V6. I'll post a picture tomorrow

02-18-2009, 08:49 PM

#36

yeewiz

Join Date: Nov 2008

Location: Concord, CA

Posts: 43

Hi Juno, here's the picture:

http://flickr.com/photos/bmw2002/3291212571/

If you look at the lower nipple right above the lower hose, there's a small plastic line that is detached. That's the port labeled "A/C". The other end of that small line ends 18" away not connected to anything. A diagram of this block and that small line and where it goes is what I'm looking for. Thanks for your help!

02-18-2009, 11:29 PM

#37

Juno

2nd Gear Member

Thread Starter

Join Date: Nov 2008

Location: NJ

Posts: 236

Quote:

Originally Posted by yeewiz

I dont see anything in OnDemand but i also have an 98 Mustang, and i will look tomorrow for it, but about what port are you talking about, the third one?