hydraulic throw out bearing - Page 2 - MustangForums.com

Go Back   MustangForums.com > Ford Mustang Tech > 2005-2014 Mustangs > GT S197 General Discussion

GT S197 General Discussion This section is for technical discussions pertaining specifically to the V8 variation of the 2005 and newer Ford Mustang.

hydraulic throw out bearing

Thread Tools Search this Thread
Old 03-06-2014, 08:48 PM   #11
Join Date: Oct 2007
Vehicle: 07 GT
Location: Maryland
Posts: 9

My 07 GT 5spd has a bad throw-out bearing. It has over 142k miles. I ordered one and am wondering how to actually install it. Can I just unbolt driveshaft, remove 02 sensor, etc, and unbolt trans case and just slide it out of the way to get access? I can't find anything online describing steps to actually replace the throw-out bearing.
rayfromtexas is offline   Reply With Quote
Old 03-07-2014, 03:37 PM   #12
5th Gear Member
dlazrael's Avatar
Join Date: May 2005
Vehicle: 08 Ford Mustang GT
Location: Maryland
Posts: 2,107
DLAzrael43 DLAzrael
Send a message via AIM to dlazrael Send a message via Yahoo to dlazrael

To do the TOB you need to drop the transmission, if you do it, might as well do the clutch and resurface or replace the flywheel itself.

And for those about OEM, I grabbed the Exedy one with my exedy clutch and FW, absolutely NO issues with it so far....
2008 Ford Mustang GT:
Go Fast Parts: 2.3L W140AX FRPP Whipple 550 HO Supercharger, PCV Delete, Pypes Violators Axleback, MAC Prochamber, FRPP 62mm Polished TB
Suspension: Steeda: Front/Rear Sways, Sport Springs, Pro-Action S/S, Chromoly LCA, Chromoly UCA, GT500 Strut Mounts
Driveline:Steeda Tri-Ax, DSS 4" Aluminum DS
Show:GT500 Spoiler, GT500 Chinstrap (awaiting install), GTS-IV Hood
dlazrael is offline   Reply With Quote


Similar Threads
Thread Thread Starter Forum Replies Last Post
What other parts should I be concerned about if my pinion bearing went bad? KingRando 2005-2014 Mustangs 5 10-02-2015 09:06 AM
cost to rebuild heads Drastang 4.6L (1996-2004 Modular) Mustang 2 09-30-2015 04:48 AM
Please help! 10 Check engine codes mrtrodonet V6 (1994-2004) Mustangs 1 09-29-2015 12:13 PM
Loss of power after changing throw out bearing Offendant V6 (1994-2004) Mustangs 6 09-23-2015 08:21 PM
Convertible Hydraulic Cylinder Mikett V6 (1994-2004) Mustangs 2 09-12-2015 11:52 PM

92, bearing, bearings, clip, cylinder, fourth, gear, gt, hydraulic, line, mustang, reliable, slave, speed, swap, throwout

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump


All times are GMT -5. The time now is 01:22 PM.

This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company