BUILT Mustang GT vert part out(omaha local only)
#1
BUILT Mustang GT vert part out(omaha local only)
Category: Drivetrain
Price: $100
Private or Vendor Listing: Private Listing
Part fits: SN95, New Edge
Location (State/Prov): NE
Item Condition: Used
NO I will not sell you the vert top lol. Being a vert owner, I know this is going to be a big item. But I plan to sell the shell, and no one wants a car without a roof.
Ok, if it's not listed, and you need it, ask about it. But here are the larger items I want to let go before I sell all the little things:
Full front end:
-Tubular K-member
-Tubular control arms
-coilovers
-struts
-brakes
-hubs
-Caster/camber plates
-all poly bushings
-
-will even throw in the steering rack
If it bolts to the K-member, I would love to sell it as a whole piece. Would make one hell of a front end upgrade all at once!
$1200obo
Full rear end:
-8.8 rear end/4.10 gears/28 spline posi and axles
-hubs
-brakes
-KYB shocks
-Eibach springs
-Hotchkis tubular control arms
-sway bar
Basically everything from the shock towers to the wheel studs.
Also included are a BRAND NEW set of 4.10 gears, and master install/bearing kits.
$800obo
DSS stroker long block(stroker kit[5.0], block, heads etc.):
Because of the timing jump and slight valve contact, the valves would need to be replaced and the head pressure tested. Everything else is fine(including the pistons! carbon got nicked, and maybe some slight marks in pistons, but they were looker over and deemed perfectly fine).
-Flat top forged pistons
-Forged I-beam rods
-8 bolt crank
-comp XE270AH cams
-ported/polished heads
-all timing stuff including cover
Basically everything from valve covers(including intake mani) to the oil pan, except any peripherals unless requested at an extra charge.
$1200obo this has about 15K miles on it before the timing jump.
Florida50 race pod gauge cluster. Has turn signal and high beam lights.
-Autometer Lunar 3 3/8" self-learning speedo/odo. The kind you set with Autometer's fancy driving learn technique. No speedcal or aftermarket gear needed!
-Autometer Lunar 3 3/8" electric tach
-2 1/6" Lunar temp gauge(mechanical)
-2 1/6" Lunar oil pressure gauge (mechanical)
ALSO INCLUDING 2 gauge pillar pod with 2 1/6" Ultralite fuel and voltage gauges
$400obo for it all
Shell:
if everything above sells, I will be parting the shell and you could buy the vert top, UNLESS someone wants the entire chassis as-is with wiring and interior and all that crap. I will cut a hell of a deal if I sell everything listed above, and someone wants everything that's left over.
If you want everything listed, all together, just trailer the car and parts home for your own project, I will sell it all together for $3K out the damn door!
Thanks for looking, hopefully we can work this all out. I hate to let it go, but life kicked me in the ***** in the middle of fixing it and trying to get back on the road. Parting it or selling it is FAR less time consuming and stressful for me than finishing
PICS:
#2
Seriously guys? PLEASE tell me someone local wants some large stuff. I will ship things like gauges and smaller things like cams(IF I get interest in other things!)
If someone wants the rotating assembly/shortblock, I will sell the cams, then sell the bare heads.(ported/polished professionally. No homebrew dremel ****)
If someone wants the rotating assembly/shortblock, I will sell the cams, then sell the bare heads.(ported/polished professionally. No homebrew dremel ****)
#3
Seriously guys? PLEASE tell me someone local wants some large stuff. I will ship things like gauges and smaller things like cams(IF I get interest in other things!)
If someone wants the rotating assembly/shortblock, I will sell the cams, then sell the bare heads.(ported/polished professionally. No homebrew dremel ****)
If someone wants the rotating assembly/shortblock, I will sell the cams, then sell the bare heads.(ported/polished professionally. No homebrew dremel ****)
Nevermind new set ordered
Last edited by jt02gt; 06-17-2010 at 10:37 PM.
#4
The reason i want them to go with whoever buys the rear-end is that the current gears were not set perfect and have started whining. I MIGHT sell them on their own, but if you don't mind, let me see what I can do about finding buyers for bigger things first.
#6
Caster/camber plates:
Would you be willing to ship those?
What Brand? Price? Will they fit New Edge?
Shoot me a pm
Would you be willing to ship those?
What Brand? Price? Will they fit New Edge?
Shoot me a pm
#7
#9
Same question as before are you selling the tranny and if so how many miles on it and is it original? I would be willing to drive to Omaha I have a plant in Aurora that I visit ona monthly basis so I come that way pretty often. Let me know I have a 98 SVT CObra that is in need of a new tranny here real soon.
Thank.
Thank.