MustangForums.com - Search Results

Go Back   MustangForums.com > Search Forums
Sign in using an external account
Register Forgot Password?
Search


Welcome to Mustang Forums!
Welcome to Mustang Forums.

You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join our community today!


Showing results 1 to 25 of 53
Search took 0.03 seconds.
Search: Posts Made By: corker
Forum: V6 (1994-2004) Mustangs 06-11-2015, 07:30 AM
Replies: 6
Views: 507
Posted By corker
This is a fairly simple job. You can just...

This is a fairly simple job. You can just replace the PW motor - once you remove the door panel and moisture barrier behind it, the motor is held in place with 3 mounting screws. Motor doesn't need...
Forum: V6 (1994-2004) Mustangs 06-05-2015, 07:04 AM
Replies: 6
Views: 284
Posted By corker
Petrock is spot on, Sounds like you found your...

Petrock is spot on, Sounds like you found your problem. Replace the hose and see how it runs when cold.
Forum: V6 (1994-2004) Mustangs 06-01-2015, 02:24 PM
Replies: 6
Views: 222
Posted By corker
Here's the wiring diagram should you have a...

Here's the wiring diagram should you have a problem again.
http://cimg7.ibsrv.net/gimg/mustangforums.com-vbulletin/1540x2000/80-mustang_ac_107aa4e54b0423108192548363db11147e175cf3.jpg
Forum: V6 (1994-2004) Mustangs 06-01-2015, 02:19 PM
Replies: 6
Views: 222
Posted By corker
Glad you were successful & nice job with the...

Glad you were successful & nice job with the Radio Shack substitute relay. This is the type of problem where a shady shop could replace the relay and sell you a new system-compressor and all....
Forum: V6 (1994-2004) Mustangs 06-01-2015, 07:48 AM
Replies: 6
Views: 222
Posted By corker
Yes, the pressure you are seeing on your A/C...

Yes, the pressure you are seeing on your A/C gauge is normal. Once the compressor shuts down the high & low sides will equalize.

I am looking at a 2000 V6 wiring diagram. It looks like the PCM...
Forum: V6 (1994-2004) Mustangs 06-01-2015, 07:28 AM
Replies: 6
Views: 284
Posted By corker
You can spray throttle body cleaner and listen...

You can spray throttle body cleaner and listen for a rise in RPM - I prefer a safer method and spray water and listen for sucking noise and engine stumble. Spray all around plastic intake runners...
Forum: V6 (1994-2004) Mustangs 05-29-2015, 07:20 AM
Replies: 6
Views: 284
Posted By corker
Check for a vac leak when cold. Engine operates...

Check for a vac leak when cold. Engine operates in open loop when cold - PCM ignores certain sensor inputs when cold. Once into closed loop, PCM compensates for vac leak lean condition and engine...
Forum: V6 (1994-2004) Mustangs 05-26-2015, 03:08 PM
Replies: 14
Views: 513
Posted By corker
I'm curious as to how you found the problem. Did...

I'm curious as to how you found the problem. Did you go back to that cable because you put a washer on it, or did you find it through the voltage drop method?
Thanks,
Corky
Forum: V6 (1994-2004) Mustangs 05-22-2015, 07:22 AM
Replies: 14
Views: 513
Posted By corker
A few things to check below: Turn headlights on...

A few things to check below:
Turn headlights on & turn key to start and watch lights, if they go real dim, check battery. If they remain bright continue checking.
Turn engine over by hand just to...
Forum: V6 (1994-2004) Mustangs 05-11-2015, 12:05 PM
Replies: 15
Views: 478
Posted By corker
Specs are from Mitchell, see attached ...

Specs are from Mitchell, see attached
http://cimg2.ibsrv.net/gimg/mustangforums.com-vbulletin/1540x2000/80-mustang_fuel_pressure_1de5dbe3b5d25a35b1066ac83f7891c59ab6d999.jpg
Forum: V6 (1994-2004) Mustangs 05-11-2015, 10:30 AM
Replies: 15
Views: 478
Posted By corker
I am pretty sure the 2000 is not a returnless...

I am pretty sure the 2000 is not a returnless system. You'll have to have a look at the Fuel Rail for the FPR. FP specs are below:

KOEO 35 - 50psi
KOER 25 - 40psi

You definitely got...
Forum: V6 (1994-2004) Mustangs 05-07-2015, 08:07 AM
Replies: 1
Views: 157
Posted By corker
Check power and grounds first - see diagram below...

Check power and grounds first - see diagram below
Corky



http://cimg0.ibsrv.net/gimg/mustangforums.com-vbulletin/1540x2000/80-mustang_cruise_a98a102e1e571b1004254b55c26898e22fbdeba2.jpg

...
Forum: V6 (1994-2004) Mustangs 03-16-2015, 10:18 AM
Replies: 9
Views: 353
Posted By corker
Back up to the zero fuel pressure. First check...

Back up to the zero fuel pressure. First check your fuel pressure gauge on a known good car. If you still have 0 fuel pressure find out why. I have seen a pump wired backwards when only the fuel...
Forum: V6 (1994-2004) Mustangs 03-11-2015, 10:44 AM
Replies: 5
Views: 425
Posted By corker
Check out everything first - ignition, fuel and...

Check out everything first - ignition, fuel and engine mechanicals (compression). I had the same problem with a 2000 Mustang V6. I eliminated all possibilities I could think of and then replaced...
Forum: V6 (1994-2004) Mustangs 02-11-2015, 01:11 PM
Replies: 5
Views: 323
Posted By corker
Replace motor mounts, trans mount, replace RT...

Replace motor mounts, trans mount, replace RT side exhaust manifold if cracked (most are), upper & lower radiator hoses, heater hoses... look over anything that is buried in the back of the engine...
Forum: V6 (1994-2004) Mustangs 02-11-2015, 12:55 PM
Replies: 6
Views: 361
Posted By corker
Here is a good video to watch to learn about how...

Here is a good video to watch to learn about how the fuel pump circuit operates - check it out.
https://www.youtube.com/watch?v=Rwve6lXriO4

Corky
Forum: V6 (1994-2004) Mustangs 02-11-2015, 06:36 AM
Replies: 6
Views: 361
Posted By corker
Yep, you got a few extra wires in the second...

Yep, you got a few extra wires in the second picture. You probably need a wiring diagram for both models and compare side by side. You can figure this out by a diagram.
If you jump around the...
Forum: V6 (1994-2004) Mustangs 02-10-2015, 02:23 PM
Replies: 6
Views: 361
Posted By corker
There are always subtle differences from...

There are always subtle differences from year-to-year and sometimes within the same year. It sounds like you are caught up in one of the changes. Let's take one problem at a time - let's try to get...
Forum: V6 (1994-2004) Mustangs 02-10-2015, 07:50 AM
Replies: 16
Views: 1,062
Posted By corker
A couple of checks: Check your engine to...

A couple of checks:
Check your engine to chassis ground wire to ensure it is there and make sure it is clean and tight.
Do a voltage drop test on the positive battery cable to the starter...
Forum: V6 (1994-2004) Mustangs 01-28-2015, 02:25 PM
Replies: 6
Views: 360
Posted By corker
I am not familiar with the differences in the '94...

I am not familiar with the differences in the '94 & '01 wiring harnesses, but maybe you have that worked out. In simple terms, the crank pos sensor(CPS) sends a signal to the Ign cntrl mod (ICM),...
Forum: V6 (1994-2004) Mustangs 01-26-2015, 08:02 AM
Replies: 1
Views: 155
Posted By corker
You've got a problem with the heater circuit in...

You've got a problem with the heater circuit in the O2 sensor after the CAT. The PCM monitors this circuit all the time, but calls on it during cold starts. The O2 sensor has a small heater in it...
Forum: V6 (1994-2004) Mustangs 01-26-2015, 07:49 AM
Replies: 6
Views: 331
Posted By corker
You can always splice it temporarily, but that is...

You can always splice it temporarily, but that is a last ditch effort to alter the factory connection. I would try to connect it and use a few zip ties to hold the connector in place. Did you check...
Forum: V6 (1994-2004) Mustangs 01-22-2015, 10:28 AM
Replies: 11
Views: 659
Posted By corker
Sorry, I can't help here. I use my buddy's Snap...

Sorry, I can't help here. I use my buddy's Snap On scanner when I have problems (ridiculously expensive). There have been so many changes recently to scanner apps. There are blue tooth ones that...
Forum: V6 (1994-2004) Mustangs 01-22-2015, 07:31 AM
Replies: 11
Views: 659
Posted By corker
Before you throw more money at this problem,...

Before you throw more money at this problem, invest in a scanner and take a look at live data while the problem is happening. Post result here and we can help you pinpoint the problem. Tough to...
Forum: V6 (1994-2004) Mustangs 01-22-2015, 07:21 AM
Replies: 6
Views: 331
Posted By corker
If cam sensor was changed at one time before,...

If cam sensor was changed at one time before, there are 2 different types of sensors, stepped and non-stepped and the electrical connector blades are different. check the video below, somewhere...
Showing results 1 to 25 of 53

 
Forum Jump
Advertising

Featured Sponsors
Vendor Directory
New Sponsors
All times are GMT -5. The time now is 10:38 PM.

© Internet Brands, Inc.


This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. Ford® is a registered trademark of the Ford Motor Company
Emails Backup