MustangForums.com - Search Results

Go Back   MustangForums.com > Search Forums
Search


Showing results 1 to 10 of 10
Search took 0.01 seconds.
Search: Posts Made By: randys85
Forum: Speed Density/Carb/SSP section 10-22-2013, 11:54 PM
Replies: 0
Views: 563
Posted By randys85
ho vs non ho

Was wondering if anybody knows if theres a difference in power or sound if you would build two identicle 302 motors, carb with dual plane intake, but one would have ho firing order other would have...
Forum: General Tech 10-07-2013, 08:13 AM
Replies: 12
Views: 796
Posted By randys85
Computer was already replaced

Computer was already replaced
Forum: General Tech 10-05-2013, 04:48 AM
Replies: 12
Views: 796
Posted By randys85
Ive tried the tlmlng at multiple spots, still no...

Ive tried the tlmlng at multiple spots, still no power off the line
Forum: General Tech 10-04-2013, 10:37 AM
Replies: 12
Views: 796
Posted By randys85
I finally got a new code reader. No codes only 11...

I finally got a new code reader. No codes only 11 system fine, did onboard cylinder check got code 90 which is all cylinders good, timing is at 16 with plug undone, tps is 89v and 4.64 at wot. New...
Forum: 5.0L (1979-1995) Mustang 09-24-2013, 10:56 PM
Replies: 1
Views: 626
Posted By randys85
is there a difference between 89-90 & 91up computers

working on project and while trying to do wiring I noticed that 89-90 has pin 57 tied in with the red wires but 91 up doesn't list that pin, also in wiring diag. 89-90 pin 6 goes to vss but in the...
Forum: General Tech 09-16-2013, 01:54 PM
Replies: 12
Views: 796
Posted By randys85
At idle pressure is 30-32 if I crack on it quick...

At idle pressure is 30-32 if I crack on it quick it jumps to 40. If I disconnect vaccum and plug the port it is at 38-40 at idle right now I have a harbor freight gauge so not sure how accurate it...
Forum: General Tech 09-16-2013, 07:28 AM
Replies: 12
Views: 796
Posted By randys85
All sensors and computer were replaced and no...

All sensors and computer were replaced and no codes aftr checkin and dumping the codes
Forum: General Tech 09-15-2013, 02:51 PM
Replies: 12
Views: 796
Posted By randys85
Basically powerbrakes fine. Before exhaust was...

Basically powerbrakes fine. Before exhaust was welded from a stop and you stand on it the tires would break loose and a soda bottle would flip out the cup holder. Now the tires don't brake loose and...
Forum: General Tech 09-15-2013, 02:44 PM
Replies: 12
Views: 796
Posted By randys85
My pressure goes up to 40 then comes back down to...

My pressure goes up to 40 then comes back down to 35 when driving. The plugs are white/grayish. Before the exhaust was very rich now seems right where it should be
Forum: General Tech 09-14-2013, 05:51 PM
Replies: 12
Views: 796
Posted By randys85
still not right

I have a 91 gt auto tranny after putting on mac shorties offroad h pipe and bullit straight through mufflers then turnouts on all with clamps car ran fine. Took clamps off and welded it all. Now...
Showing results 1 to 10 of 10

 
Forum Jump
 

All times are GMT -5. The time now is 07:28 AM.



This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company