MustangForums.com - Search Results

Go Back   MustangForums.com > Search Forums
Search


Showing results 1 to 25 of 499
Search took 0.30 seconds.
Search: Posts Made By: MonsterBilly
Forum: Classic Mustangs (Tech) 08-13-2016, 09:15 AM
Replies: 21
Views: 1,266
Posted By MonsterBilly
Where in Europe are you. I am in Paris for the...

Where in Europe are you. I am in Paris for the next week. I know a lot about these cars.
Forum: Classic Mustangs (Tech) 07-16-2016, 09:40 AM
Replies: 3
Views: 281
Posted By MonsterBilly
I did the borgenson power sterring conversion. I...

I did the borgenson power sterring conversion. I like it okay but im not crazy about it.

it is much much better than the factory power steering though.
Forum: Classic Mustangs (Tech) 07-16-2016, 09:30 AM
Replies: 8
Views: 440
Posted By MonsterBilly
also check the valve covers. What kind of valve...

also check the valve covers. What kind of valve covers do you have. I had a similar issue when i did a rebuild. I put a new set of valve covers and they did not have a splash guard below the hole for...
Forum: Classic Mustangs (Tech) 05-24-2016, 09:58 AM
Replies: 3
Views: 212
Posted By MonsterBilly
i had a bad vibration on the highway for over 4...

i had a bad vibration on the highway for over 4 years. I could not figure out what it was. It ended up being the pinion shaft in the rear end. it gave out on me one day, i had it rebuilt and now...
Forum: 5.0L (1979-1995) Mustang 05-20-2016, 09:13 AM
Replies: 7
Views: 377
Posted By MonsterBilly
I did have those same problems, its mostly a...

I did have those same problems, its mostly a tuning issue.
Go the msd forum and it will explain how to remedy those problems. Its mostly the cam profile and the squirt setting. Also, adjusting the...
Forum: Classic Mustangs (Tech) 05-13-2016, 12:21 AM
Replies: 9
Views: 506
Posted By MonsterBilly
You would be better off keeping that car as it....

You would be better off keeping that car as it. Then pick up another car closer to what you want. Then make the changes to the new one to get it exactly where you want it performance wise.
Forum: Classic Mustangs (Tech) 05-13-2016, 12:17 AM
Replies: 12
Views: 652
Posted By MonsterBilly
Yes I did, however, i bought the saginaw pump...

Yes I did, however, i bought the saginaw pump from summit. I picked up the Tuff Stuff brand pump
Forum: Classic Mustangs (Tech) 05-12-2016, 08:55 AM
Replies: 12
Views: 652
Posted By MonsterBilly
but then again, i put the MSD Atomic EFI on my...

but then again, i put the MSD Atomic EFI on my car and i HATE it. i am switching back to a carb and putting the efi on my 75 bronco.

my 331 is built too much for the efi to run smooth. I have a...
Forum: Classic Mustangs (Tech) 05-12-2016, 08:47 AM
Replies: 12
Views: 652
Posted By MonsterBilly
i like it but im not crazy about it. I had a...

i like it but im not crazy about it. I had a tough time getting it to handle right. It still grabs the road if there is a ridge or a hump in the middle.

also, the lines that come with it are so...
Forum: Classic Mustangs (Tech) 05-11-2016, 09:56 AM
Replies: 12
Views: 652
Posted By MonsterBilly
i upgraded my factory ps to the borgenson unit....

i upgraded my factory ps to the borgenson unit. if i had it to do over again i would go electric
Forum: Classic Mustangs (Tech) 05-11-2016, 09:27 AM
Replies: 2
Views: 132
Posted By MonsterBilly
my buddy has a similar issue on a 55 f100 that...

my buddy has a similar issue on a 55 f100 that has a 302 in it with a mustang 2 front end. he got a factory hose and had the fitting on one end changed at shop which makes custom hoses. Im not sure...
Forum: Classic Mustangs (Tech) 05-02-2016, 09:40 PM
Replies: 28
Views: 952
Posted By MonsterBilly
There are two firing orders. You stated a windsor...

There are two firing orders. You stated a windsor firing order but there is a different order for the 351 than the 289/302. when i replaced my cam, even though it said it was for a 289/302, it was...
Forum: Classic Mustangs (Tech) 04-11-2016, 11:17 PM
Replies: 13
Views: 829
Posted By MonsterBilly
i twill aminly depend on the offset of the wheel...

i twill aminly depend on the offset of the wheel you want to use. I picked up a 8.8 explorer rear end and cut 2.25 inches shorter to work. it worked great for 8 years till it broke. i just had it...
Forum: Classic Mustangs (Tech) 03-12-2016, 12:40 AM
Replies: 3
Views: 293
Posted By MonsterBilly
It's did amps in the trunk, 6x9 speakers in the...

It's did amps in the trunk, 6x9 speakers in the package tray and kick panels with 6 inch speakers and separate tweets.
Then I ran a wire from my amp, under my carpet to the hump hugger console. I...
Forum: Classic Mustangs (Tech) 02-25-2016, 04:43 PM
Replies: 11
Views: 520
Posted By MonsterBilly
i have a 331 with tfs 170 heads. I am putting...

i have a 331 with tfs 170 heads. I am putting down 399 hp and 420ftlbs at the flywheel. or at least was before i installed the crappy atomic efi.

IMO you must get bigger heads. see the post above....
Forum: Classic Mustangs (Tech) 02-25-2016, 09:20 AM
Replies: 7
Views: 357
Posted By MonsterBilly
i have the 4.5 mid eye springs. i like them a lot...

i have the 4.5 mid eye springs. i like them a lot I am running them with bilstien shocks. i could not imagine the 5 leaf springs. i would think they would be too stiff. mine are as stiff as i think i...
Forum: Classic Mustangs (Tech) 02-22-2016, 07:29 AM
Replies: 13
Views: 629
Posted By MonsterBilly
I'm looking to use what I have on the shelf. I...

I'm looking to use what I have on the shelf. I have enough parts left over from the last couple years to build a few engines. The bronco is just a mild cruiser.
The heads i have, and intake,...
Forum: 5.0L (1979-1995) Mustang 02-18-2016, 08:41 AM
Replies: 7
Views: 377
Posted By MonsterBilly
i had it on my 68 bronco with a 302 and it worked...

i had it on my 68 bronco with a 302 and it worked fine. I now have it installed on my 66 mustang and it runs pretty good. I have not driven it yet, only backed it in and out of the driveway. I still...
Forum: Classic Mustangs (Tech) 02-16-2016, 09:17 PM
Replies: 13
Views: 629
Posted By MonsterBilly
I'm not sure if they have air ports. It did have...

I'm not sure if they have air ports. It did have a smog pump which has since been removed if that is any in inclination

I have not taken the intake and heads off of the 75 yet. It runs fine I just...
Forum: Classic Mustangs (Tech) 02-15-2016, 11:19 PM
Replies: 13
Views: 629
Posted By MonsterBilly
any difference in 289 vs. 302 heads

I have a set of 289 h a ads from my mustang. They have been ported and have screw in studs with guide plates and a recent valve job with some good solid springs.

I picked up a 75 bronco with a 302...
Forum: Classic Mustangs (Tech) 02-13-2016, 11:52 PM
Replies: 15
Views: 540
Posted By MonsterBilly
http://cimg9.ibsrv.net/gimg/mustangforums.com-vbul...

http://cimg9.ibsrv.net/gimg/mustangforums.com-vbulletin/2000x1124/80-20160207_155440_ab57ddac84daed83e6e670859b925b4185a1c904.jpg

...
Forum: Classic Mustangs (Tech) 02-13-2016, 11:44 PM
Replies: 7
Views: 256
Posted By MonsterBilly
Thanks Groho, You were correct. Different...

Thanks Groho,
You were correct. Different threads on the hose coupling than what was needed. Luckily the Dakota Digital VHX kit came with several different types fittings and their was one in the...
Forum: Classic Mustangs (Tech) 02-09-2016, 10:27 PM
Replies: 15
Views: 540
Posted By MonsterBilly
it is a lot of work, i wish it would have...

it is a lot of work, i wish it would have researched it a better first. I am also installing atomic efi, and a set of dakota digital vhx gauges at the same time. with the dakota set i didnt need half...
Forum: Classic Mustangs (Tech) 02-09-2016, 09:28 PM
Replies: 7
Views: 256
Posted By MonsterBilly
sending unit questions

so i am deep into a big project. I am installing all new wiring, dakota digital gauges and atomic efi all at once.

the issue i am having is with the sending units.

both the atomic efi and the...
Forum: 5.0L (1979-1995) Mustang 02-08-2016, 11:03 PM
Replies: 7
Views: 377
Posted By MonsterBilly
Atomic EFI?

Is anyone running the Atomic EFI? and , If so, what cam do you have?

I am in the process of installing a Painless wiring kit into my 66 and decided on all new gauges and the Atomic EFI since i...
Showing results 1 to 25 of 499

 
Forum Jump
 

All times are GMT -5. The time now is 08:51 PM.



This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company