what carb and intake manifold - Page 2 - MustangForums.com

Go Back   MustangForums.com > Ford Mustang Tech > 5.0L (1979-1995) Mustang > Speed Density/Carb/SSP section

Speed Density/Carb/SSP section This section is for the Speed Density or Carb vehicles, as well as Special Service Package 'Stangs

what carb and intake manifold

Thread Tools Search this Thread
Old 01-30-2011, 11:27 PM   #11
5th Gear Member
Join Date: Aug 2004
Vehicle: 84 Mustang, 59 Ranchero
Location: Arizona
Posts: 4,103

I think I'd use an RPM air-gap intake and a 650 mechanical secondary.
You don't have the cam or heads to be in Vic Jr/750 country..........
GOOD,FAST, CHEAP-----------YOU CAN ONLY GET 2 OUT OF 3!!!!!!!!!!!!!!!!
tinman is offline   Reply With Quote
Old 01-31-2011, 06:06 PM   #12
1st Gear Member
pete88gt's Avatar
Join Date: Aug 2008
Vehicle: '88 GT
Location: GA
Posts: 139

bump. 670 street avenger is what I run and i love it, but a 302 with smaller aluminum heads would still be fine with a 600cfm carb
88GT: Fresh 306, Speed Pro pistons, 170 TFS TW Heads, E-303 cam, 1.6 SVO RR, Wieand Stealth Intake, 670 Street Avenger Holley Carb, Full MSD, Rebuilt T-5, Taurus Fan, Hurst/Pro 5.0 Shifter, 3.73s, FRPP Aluminum Drive Shaft, BBK UD Pulleys, PA Perf. 130amp alt., BBK Ceramic LT Headers, BBK OR H-Pipe, Nitto NT555r tires.
pete88gt is offline   Reply With Quote
Old 05-11-2011, 08:47 PM   #13
1st Gear Member
stangfreak09's Avatar
Join Date: Jan 2011
Vehicle: 87' lx
Location: missouri
Posts: 76

i would go with a performer rpm and holley 650 i had that setup and was pretty fast for a stock motor. i ran off on a s/c harley truck with that setup.
stangfreak09 is offline   Reply With Quote
Old 07-01-2011, 03:46 AM   #14
Join Date: Nov 2009
Vehicle: 1986 gt hatch
Location: WA
Posts: 15

i agree with tinman. seems to be pretty easy to tune and good all around performance
load1234 is offline   Reply With Quote
Old 08-29-2011, 12:21 AM   #15
1st Gear Member
86blackgt's Avatar
Join Date: Apr 2009
Vehicle: 86 ford mustang
Location: az
Posts: 85

i had a coupe that had the same set that you have and i ran a weiand x-celeator and a holley 650 dp. the car went low 12s durring the hot summers in az. its was a great combo.
stock 86 bottom end with 210k, e303 cam, e7 heads with 1.6 rollor rockers, victor 50 intake, 19 lb injectors, kirban adj regulator, 75mm tb, 76 mm air meter, mac cold air, electric fan, stock pressure plate with mcleod disc, 3.73 gears,qa1 kmember w coil overs, stock rear controll arms, and 26x11.50 et streets, 11.56 @ 121 on a 125 shot, 12.65 on motor
new motor gt40p heads,hurricane, carb236,232 and 565,545lift cammotion cam 150 wet kit11.26 @125, on motor 12.17 @ 112
86blackgt is offline   Reply With Quote
Old 06-29-2014, 02:23 PM   #16
2nd Gear Member
Join Date: Mar 2005
Location: south carolina
Posts: 295

i am very pleased with my Quickfuel 650 DP
1990 lx,gt40 crate engine,ported and polished gt40x heads,30# injectors,kurban fuel pressure reg,cold air tube,e303,griffin3core/blackmagic fan,cobra intake,cc 125 shot wet kit,bbk long tubes/or xpipe w/flows/wc t5 w/hurst short throw/and 3.73's

1990 lx coupe..carbed Quickfuel 650, Lunati cam, rpm upper, msd ignition, bbk shorties xpipe and flows dumped, T5Z transmission with 3.73 gears and a few more goodies....358rwhp and 323ft lbs torque
gambit90lx is offline   Reply With Quote
Old 07-03-2014, 07:18 PM   #17
6th Gear Member
bluebeastsrt's Avatar
Join Date: Jun 2006
Vehicle: 1995 mustang GT
Location: Jersey
Posts: 11,243

Originally Posted by tinman View Post
I think I'd use an RPM air-gap intake and a 650 mechanical secondary.
You don't have the cam or heads to be in Vic Jr/750 country..........
I pretty much second this. Only I'd use vacuum secondaries. I'm personally a big fan of Holley carbs. I'm going to use one on my 363.
bluebeastsrt is offline   Reply With Quote


Similar Threads
Thread Thread Starter Forum Replies Last Post
Original Owner 1970 Mustang b8checker Classic Mustangs (Tech) 8 10-08-2015 12:55 PM
S197 Parts baddog671 Parts For Sale 6 10-07-2015 11:36 PM
Original Owner 1970 Mustang b8checker New Member Area 3 09-30-2015 07:11 AM
Snow performance stage 2 MAF boos cooler install jwog666 Pipes, Boost & Juice 2 09-29-2015 06:05 PM
Hello All RCS02v6 New Member Area 4 09-29-2015 01:46 PM

1995, 302, 50, 94, cam, carb, carburetor, density, gt, gt40, heads, intake, manifold, mustang, speed, works, x303

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump


All times are GMT -5. The time now is 09:24 AM.

This forum is owned and operated by Internet Brands, Inc., a Delaware corporation. It is not authorized or endorsed by the Ford Motor Company and is not affiliated with the Ford Motor Company or its related companies in any way. FordŽ is a registered trademark of the Ford Motor Company