Rats ate some of my harness :(
04-24-2013, 12:55 AM
#1
Thread Starter
Join Date: Apr 2013
Location: arizona
Posts: 12
Rats ate some of my harness :(
Hey all, so my in laws stock, 05 mustang(v6) has a cel due to bank 1 sensor 1 or sensor, I thought nothing and had them order the Parr and replaced it for them, well I turned the car and the same stupid code is their for the same exact part, closer examination and what do I see? The wiring for the passenger side of the of sensor wiring has been chewed up, the wires are still in tact but missing the shield. My problem is, I can't resplice it cuz theirs absolutely no room being that the top of the trans is behind the motor, below the firewall. Is it a pain to drop the whole harness to drop that portion of wiring down? Or am I screwed?
04-24-2013, 11:11 AM
#2
Cut & Paste Expert
Join Date: May 2007
Location: NW Arkansas
Posts: 13,322
http://iihs.net/fsm/?dir=40&viewfile...20-%204.0L.pdf
I would suspect that you will have to drop the tranny to access the wiring harness.
It goes directly to the PCM without going thru any connectors.
I would suspect that you will have to drop the tranny to access the wiring harness.
It goes directly to the PCM without going thru any connectors.
04-24-2013, 02:11 PM
#4
Gentleman's Relish
Join Date: Feb 2005
Location: AZ
Posts: 13,090
Anything is possible but probable is another story 
Unless you have nimble alien like fingers/hands and you can get into the area where the wires are, cut them, and then reconnect them, you're stuck having to drop the tranny to gain access.
The other thought is to see if you can find the wire at the PCM side, cut it few inches from the harness and then run your own length of wire to the O2 Sensor and reattaching the O2 harness at the other end thus bypassing the OEM wiring. Of course you should protect the new run of wire with wire loom just like the OEM.
Unless you have nimble alien like fingers/hands and you can get into the area where the wires are, cut them, and then reconnect them, you're stuck having to drop the tranny to gain access.
The other thought is to see if you can find the wire at the PCM side, cut it few inches from the harness and then run your own length of wire to the O2 Sensor and reattaching the O2 harness at the other end thus bypassing the OEM wiring. Of course you should protect the new run of wire with wire loom just like the OEM.
04-26-2013, 01:57 PM
#7
6th Gear Member
Join Date: Jul 2008
Location: Acworth, GA
Posts: 12,260
04-26-2013, 02:46 PM
#8
Cut & Paste Expert
Join Date: May 2007
Location: NW Arkansas
Posts: 13,322
Been waiting long?
I got mine in 2007 when I bought my 2007 Mustang.
www.mustangsunlimited.com has them for sale and
has had them available for quite a while.
I got mine in 2007 when I bought my 2007 Mustang.
www.mustangsunlimited.com has them for sale and
has had them available for quite a while.
04-26-2013, 09:35 PM
#9
Thread Starter
Join Date: Apr 2013
Location: arizona
Posts: 12
Uggggh I can't view the pic or link u posted bro cuz I guess I'm new still so my account isn't letting me, could u tell me where to look for the Pcm and wiring diagram as to wat pin the bank 1 sensor 1 is for the o2,(that is the passenger side front of sensor right?
04-27-2013, 10:52 AM
#10
Cut & Paste Expert
Join Date: May 2007
Location: NW Arkansas
Posts: 13,322
Look in the printed manual.
Its not new memmer probs cuz.
Its browser probs not letting you see the pdfs. (:
And alas that info is not on the online site.
Just the printed manuals.
www.mustangsunlimited.com for the electrical workshop book...
Cant sem to find it onlne.
http://www.mustangsunlimited.com/Sub...s=LMN15&grid=N
Its not new memmer probs cuz.
Its browser probs not letting you see the pdfs. (:
And alas that info is not on the online site.
Just the printed manuals.
www.mustangsunlimited.com for the electrical workshop book...
Cant sem to find it onlne.
http://www.mustangsunlimited.com/Sub...s=LMN15&grid=N
