Whipple or KB, KB or Whipple????
#1
Whipple or KB, KB or Whipple????
Well I have been going around and around on which SC to get. I even ported the Eaton to try and delay the inevitable! No luck!!I placed the order yesterday for a new SC.I will be installing the 2.8L Kenne Bell Mammoth on my car!75mm throttle body, diablosport mafia, 75 pound injectors, boost-a-spark the whole nine yards!It shipped yesterday! Should have it on by the middle of next week! I'll take lots of pic's for you guys!
#5
RE: Whipple or KB, KB or Whipple????
ORIGINAL: PLstang
Maybe not a pilots license, but I sure would like to need my 9 second license!!!!
Hoping to get that physical pretty soon!!
Maybe not a pilots license, but I sure would like to need my 9 second license!!!!
Hoping to get that physical pretty soon!!
#7
RE: Whipple or KB, KB or Whipple????
Thanks guys!
I'm sure I don't have to tell you guys, but I already ordered the 2-1/2" pulley!!
With my Innovators West overdrive pulley this blower should make some big numbers!! With the large Afco heat exchanger and Pfab Ice tankI already have on the car I can't wait to see what she'll do in the 1/4!!!
Then once I get all the numbers and times.......I'm gonna spray it![8D]
I'm sure I don't have to tell you guys, but I already ordered the 2-1/2" pulley!!
With my Innovators West overdrive pulley this blower should make some big numbers!! With the large Afco heat exchanger and Pfab Ice tankI already have on the car I can't wait to see what she'll do in the 1/4!!!
Then once I get all the numbers and times.......I'm gonna spray it![8D]
#8
RE: Whipple or KB, KB or Whipple????
ORIGINAL: SaddleUp
Would you be willing to take anyone along for a drive to try out your new KB?!?
Would you be willing to take anyone along for a drive to try out your new KB?!?
Hey if you know any Shelby owner interested in a Ported Eaton, a small Eaton Pulley, a Metco Idler, or a C&L intake PM me!
#9
RE: Whipple or KB, KB or Whipple????
PLstang,
You seem way crazy and more knowledgeable than most so I have a question for you. What are your thoughts on the new Roush TVS2300 SC?
I was going to get the Whipple HO but a friend works at Roush and I can get it at Employee Cost. I don't think I would go more than 10PSI with the stock motor.
I am not looking to become a track hound but would like to beat my buddy with an older Z06 someday. My car is running in the high 12's now.
My car is an 08 Mustang GT Automatic/Convertible Plus Q350 Steeda Package.
Here are my mod's:
Steeda UDP's
FRPP 3:73's
Steeda Throttle Body Delete/Charge Motion Plate
Steeda Performance CAI - Custom Tune
90 MM Mass Air
Steeda Short Headers
Steeda Axle-Back Exhaust
Steeda Sport Springs
Tokico D-Spec Shocks (not installed yet)
Spyder 1-piece drive shaft and safety loop ordered
Steeda Bump Steer Kit
Steeda G-Trac
Steeda front/rear sway bars
Steeda LCA's
Steeda Double Strut Tower Brace
What SC do you recommend for my 4.6 3V?
What else do I need to do/add when I do the SC?
I don't mean to hijack your thread so here is mine explaining my situation. I would appreciate your advice.
Here is my thread on the subject:
https://mustangforums.com/m_5300459/mpage_1/key_/tm.htm
You seem way crazy and more knowledgeable than most so I have a question for you. What are your thoughts on the new Roush TVS2300 SC?
I was going to get the Whipple HO but a friend works at Roush and I can get it at Employee Cost. I don't think I would go more than 10PSI with the stock motor.
I am not looking to become a track hound but would like to beat my buddy with an older Z06 someday. My car is running in the high 12's now.
My car is an 08 Mustang GT Automatic/Convertible Plus Q350 Steeda Package.
Here are my mod's:
Steeda UDP's
FRPP 3:73's
Steeda Throttle Body Delete/Charge Motion Plate
Steeda Performance CAI - Custom Tune
90 MM Mass Air
Steeda Short Headers
Steeda Axle-Back Exhaust
Steeda Sport Springs
Tokico D-Spec Shocks (not installed yet)
Spyder 1-piece drive shaft and safety loop ordered
Steeda Bump Steer Kit
Steeda G-Trac
Steeda front/rear sway bars
Steeda LCA's
Steeda Double Strut Tower Brace
What SC do you recommend for my 4.6 3V?
What else do I need to do/add when I do the SC?
I don't mean to hijack your thread so here is mine explaining my situation. I would appreciate your advice.
Here is my thread on the subject:
https://mustangforums.com/m_5300459/mpage_1/key_/tm.htm