Torque for 2011 v6 3.7 water pump replacement - MustangForums.com

Notices
3.7L V6 Technical Discussions Any questions about the new engine, transmission, exhaust, tuners/CAI, or gearing can be asked here!

Torque for 2011 v6 3.7 water pump replacement

Reply

 
 
 
Old 09-20-2018, 02:25 AM
  #1  
golfster
Thread Starter
 
Join Date: Sep 2018
Location: GA
Posts: 14
Default Torque for 2011 v6 3.7 water pump replacement

Replacing the water pump look to be straight forward but I can't find the spec for torque on the bolts. It would be great to get them for the thermostat housing and the water pump if anyone has the them. Thanks.
golfster is offline  
Reply With Quote
Old 09-21-2018, 05:18 AM
  #2  
08'MustangDude
4th Gear Member
 
Join Date: Jan 2018
Location: Pennsylvania
Posts: 1,482
Default

Pump:
There is also a tightening sequence...
..3 1 5 6
4 2 .. 7

Step 1 - 89 in-lbs
Step 2 - +45 degree turn
Over tightening will damage the pump.

Thermostat Housing:
..1
2 3 4

Step 1 - 71 in-lbs
Step 2 - +45 degree turn
08'MustangDude is offline  
Reply With Quote
Old 09-21-2018, 07:45 PM
  #3  
golfster
Thread Starter
 
Join Date: Sep 2018
Location: GA
Posts: 14
Default Torque

That seem really high for aluminum.

Here is what other told me the service manual has "My Chiltons manual shows 12-18 ftlbs also for the water pump bolt torque.The wp pulley to hub bolt torque is shown as
36-47 ftlbs."

Do you have a picture of the screws numbering? I normal would tighten in cross patterned. Thanks again for the advance. Did you get the torques from a Ford Service manual?
golfster is offline  
Reply With Quote
Old 09-21-2018, 11:06 PM
  #4  
AK_Kayaker
3rd Gear Member
 
AK_Kayaker's Avatar
 
Join Date: Feb 2008
Location: Anchorage, AK
Posts: 966
Default

Originally Posted by golfster View Post
That seem really high for aluminum.

Here is what other told me the service manual has "My Chiltons manual shows 12-18 ftlbs also for the water pump bolt torque.The wp pulley to hub bolt torque is shown as
36-47 ftlbs."

Do you have a picture of the screws numbering? I normal would tighten in cross patterned. Thanks again for the advance. Did you get the torques from a Ford Service manual?
You did notice he posted "in lbs" not "ft lbs".
So if you convert 89 in lbs = about 7.4 ft lbs. , which would make the numbers you posted a bit high.
AK_Kayaker is offline  
Reply With Quote
Old 09-21-2018, 11:57 PM
  #5  
golfster
Thread Starter
 
Join Date: Sep 2018
Location: GA
Posts: 14
Default Torque

I did not notice that. Thanks for point that out.

Anybody have a link to show the numbering of bolts? Plus there is video that show using RTV. Should I use RTV on both side of the gasket? When I read the forum I see both yes and no. Thoughts? I tend to use it when there isn't already a rubber seal. In this case the gasket has a rubber seal.
golfster is offline  
Reply With Quote
Old 09-22-2018, 08:20 PM
  #6  
08'MustangDude
4th Gear Member
 
Join Date: Jan 2018
Location: Pennsylvania
Posts: 1,482
Default

I showed the numbering of the bolts the best I could, the ones on the TOP
and the ones on the bottom, of the pump, and their order. Same with the
thermostat housing. I got that from my Chilton's manual, but here:

PUMP:


T-STAT HOUSING:
08'MustangDude is offline  
Reply With Quote
Old 09-22-2018, 10:01 PM
  #7  
golfster
Thread Starter
 
Join Date: Sep 2018
Location: GA
Posts: 14
Default

Thanks a ton for the information!
golfster is offline  
Reply With Quote
Reply
 
 
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
computerwizard
2005-2014 Mustangs
6
09-18-2018 08:52 AM
Gothere
3.7L V6 Technical Discussions
18
05-25-2017 08:51 PM
GStam66
4.6L (1996-2004 Modular) Mustang
1
11-24-2007 08:20 PM
thedude
5.0L (1979-1995) Mustang
3
03-03-2007 08:53 PM
musman
Classic Mustangs (Tech)
2
10-10-2006 10:37 PM

Forum Jump

Thread Tools
Search this Thread
Advertising
Featured Sponsors
Vendor Directory