MustangForums.com

MustangForums.com (https://mustangforums.com/forum/index.php)
-   4.6L (1996-2004 Modular) Mustang (https://mustangforums.com/forum/4-6l-1996-2004-modular-mustang-7/)
-   -   351W swap into 96-98 (https://mustangforums.com/forum/4-6l-1996-2004-modular-mustang/112656-351w-swap-into-96-98-a.html)

lucheski 04-05-2006 01:17 PM

351W swap into 96-98
 
I am looking at getting a 96 V6 mustang and swapping in a EFI 351W-T5 combo

Where I can find info performing this swap...

For starters I know I need the k-member and maybe some custom headers.

uberstang1 04-05-2006 03:03 PM

RE: 351W swap into 96-98
 
thats one hell of a swap

GodAmGT00 04-05-2006 03:07 PM

RE: 351W swap into 96-98
 
Well, there's the long answer, and the short...

In short, you'd need a lot, but it's well worth it if you ask me.. If you have the money, it's even more worthwile..

The long, hell, I don't know.... I'm sure there've been many people who've done this swap.. Have you checked online?? How about on this site??

Wiring harness, suspension upgrade, driveshaft, engine/tranny mounts will need to be fabbed up... There would be other things that come up.. It's most likely a completely Custom job....


JT

Acer2428 04-05-2006 05:16 PM

RE: 351W swap into 96-98
 
Check out the 351 section under 'special stangs'

w8less 04-05-2006 07:47 PM

RE: 351W swap into 96-98
 
u would need a lot but the motor mounts for a 302 will work for a 351, u need a read end a t5 barely holds a 302 i would not recommend using it with a 351 cause the torque from it will rip it apart. ummm...........kmember like some one said u can buy the drive shaft and headers for the fit but more than likely the wiring will be more a hassle then the acutal install. also trickflow edelbrock and someone else i can't remember right of hand make efi intakes for a 351 also u would need at least 24lbs injectors to feed the beast. but if u have the money its definately worth it if ur seeking some easy power.


yoteehunter 04-05-2006 08:03 PM

RE: 351W swap into 96-98
 
I would think that a wiring harnes from a 94-95 would work. The computer is for a 302 but I think it could be reburned as well. I think that would be your best bet. I have a 351 that runs, but its carbarated and I wanted to make it FI and swap like you. Good luck!

w8less 04-05-2006 08:58 PM

RE: 351W swap into 96-98
 
thats the last computer i would get those things hate cam swaps if u were to do that i would get one out of a 87-93 computer the settings are a little bit better for performance

Twister 04-05-2006 09:24 PM

RE: 351W swap into 96-98
 
It is against federal law to swap a 351 into that car

Acer2428 04-05-2006 09:45 PM

RE: 351W swap into 96-98
 
True.

You could swap a 4.6 in it though and re-register it as a GT.

jmmorgan82 04-05-2006 09:59 PM

RE: 351W swap into 96-98
 
isnt it against the law to run an off-road mid pipe too??? if so, prob more than half the people here are violating the law


All times are GMT -5. The time now is 11:51 PM.


© 2024 MH Sub I, LLC dba Internet Brands