Bumboclaat's Homecoming Part 1 *Video Up!*
#1
Bumboclaat's Homecoming Part 1 *Video Up!*
Well yall saw a little teaser yesterday. Today I went out w/ a camera man and really try to romp on her..... Unfortunatle I think the camera guy was holding on to the "oh $h!t" bar the whole time so I didn't get good driving footage.... Later on today after I let the engine cool down.... but here is an idle video and some more pics of the roll cage and other misc stuff..... Again she's 477rwhp at 8psi. Enjoy!
I'm uploading the video right now as we speak. Gimme like about 10 minutes. Also to answer yall's question about the roll cage..... Its a fully custom built roll cage by Texas Hot Rods!
I'm uploading the video right now as we speak. Gimme like about 10 minutes. Also to answer yall's question about the roll cage..... Its a fully custom built roll cage by Texas Hot Rods!
#6
RE: Bumboclaat's Homecoming Part 1
lol.... Parts list.... Here goes....
- Stage II Procharger P-1 SC with8 PSI
- 283 Built Short block, Nodular Crank, Forged Pistons, Rods, Beams, etc
- HPS Aluminum Intake Manifold
- Cobra Brake Conversion (Front)
- True Flow Intake Plenum
- 75mm Throttle Body
- Comp/Pro Series Springs
- STEEL Caster Camber Plates Shark 3 Bolt
- 90/10 Drag Strut
- Lakewood 50/50 Rear Shocks
- Lakewood Upper and Lower Control Arms
- SPEC Stage II Clutch Kit
- 31 Spline SVT Ford Posi, 31 Spline Axles & Bearings, Race Studs
- 3.73 Gears
- Fuel pressure gauge, Boost gauge, pillor mounts
- Mac Long Tube Headers
- BBK O/R X-Pipe
- SLP Loudmouth IIs
- VT Stage II Blower Cams
- Welds Prostar Racing wheels w/ M/T ET Streets, 27x10.5x15
- Stage II Procharger P-1 SC with8 PSI
- 283 Built Short block, Nodular Crank, Forged Pistons, Rods, Beams, etc
- HPS Aluminum Intake Manifold
- Cobra Brake Conversion (Front)
- True Flow Intake Plenum
- 75mm Throttle Body
- Comp/Pro Series Springs
- STEEL Caster Camber Plates Shark 3 Bolt
- 90/10 Drag Strut
- Lakewood 50/50 Rear Shocks
- Lakewood Upper and Lower Control Arms
- SPEC Stage II Clutch Kit
- 31 Spline SVT Ford Posi, 31 Spline Axles & Bearings, Race Studs
- 3.73 Gears
- Fuel pressure gauge, Boost gauge, pillor mounts
- Mac Long Tube Headers
- BBK O/R X-Pipe
- SLP Loudmouth IIs
- VT Stage II Blower Cams
- Welds Prostar Racing wheels w/ M/T ET Streets, 27x10.5x15
#7
RE: Bumboclaat's Homecoming Part 1
ORIGINAL: jpmustanggt
I'm in love. I think one of the next mods you need is to get a boost pipe and take that ugly procharger one off!
Very nice car man! When are you going to the track?
I'm in love. I think one of the next mods you need is to get a boost pipe and take that ugly procharger one off!
Very nice car man! When are you going to the track?
Boost pipe will come along with the Stage II heads, an 8 rib pulley swap to max out this blower at 14psi w/ 60lb fuel injectorsTKO 500 tranny and spec 3 clutch. New front end K-member will adjustable struts.
I'll be going to the track as soon as I find a way to change out my tires... lol. I think I threw away my car jack and tire wrench.... [:@]
#8
RE: Bumboclaat's Homecoming Part 1