Switching COP's to Coil and Wires
07-06-2008, 08:07 AM
#2
6th Gear Member
Join Date: Feb 2006
Location: Virginia
Posts: 11,786
RE: Switching COP's to Coil and Wires
You wont get much help here for that.... This site sucks for any true tech, too many know-it-all-Know-nothings. I used a 99 wiring harness that I rewired.
Here's a link to some good info.
http:// forums.corral .net/forums/ showthread.php?t=861699 Take out the spaces.
If you can get a 99+ wiring harness that would be the easiest. Took me about 1.5 to prep the w/h. There is the harder way of using the existing harness but I didn't like the idea of using a bunch of crip ends.
Here's a link to some good info.
http:// forums.corral .net/forums/ showthread.php?t=861699 Take out the spaces.
If you can get a 99+ wiring harness that would be the easiest. Took me about 1.5 to prep the w/h. There is the harder way of using the existing harness but I didn't like the idea of using a bunch of crip ends.
07-06-2008, 09:37 AM
#3
4th Gear Member
Join Date: Jan 2005
Location: Port Monmouth, New Jersey
Posts: 1,984
RE: Switching COP's to Coil and Wires
ORIGINAL: sxynerd
You wont get much help here for that.... This site sucks for any true tech, too many know-it-all-Know-nothings. I used a 99 wiring harness that I rewired.
Here's a link to some good info.
http:// forums.corral .net/forums/ showthread.php?t=861699 Take out the spaces.
If you can get a 99+ wiring harness that would be the easiest. Took me about 1.5 to prep the w/h. There is the harder way of using the existing harness but I didn't like the idea of using a bunch of crip ends.
You wont get much help here for that.... This site sucks for any true tech, too many know-it-all-Know-nothings. I used a 99 wiring harness that I rewired.
Here's a link to some good info.
http:// forums.corral .net/forums/ showthread.php?t=861699 Take out the spaces.
If you can get a 99+ wiring harness that would be the easiest. Took me about 1.5 to prep the w/h. There is the harder way of using the existing harness but I didn't like the idea of using a bunch of crip ends.
07-06-2008, 04:48 PM
#5
RE: Switching COP's to Coil and Wires
ORIGINAL: sxynerd
Stupid me for not reading the post and only the title. Reverse engineer it.... Buy a 96-98 wiring harness and add the pins you need to...
Stupid me for not reading the post and only the title. Reverse engineer it.... Buy a 96-98 wiring harness and add the pins you need to...
[sm=loser.gif][sm=laughat.gif]
07-06-2008, 05:21 PM
#6
6th Gear Member
Join Date: Feb 2006
Location: Virginia
Posts: 11,786
RE: Switching COP's to Coil and Wires
ORIGINAL: BraMas
Mike says this place is bad for tech stuff and than gives out bad tech info[sm=loser.gif][sm=laughat.gif]
ORIGINAL: sxynerd
Stupid me for not reading the post and only the title. Reverse engineer it.... Buy a 96-98 wiring harness and add the pins you need to...
Stupid me for not reading the post and only the title. Reverse engineer it.... Buy a 96-98 wiring harness and add the pins you need to...
[sm=loser.gif][sm=laughat.gif][sm=bustedsign.gif]
Not bad tech, just misunderstood.
Thread
Thread Starter
Forum
Replies
Last Post
jaiidutch
Motor Swap Section
2
09-14-2015 10:29 AM
