Mach 1 Grill delete w/ chin spoiler (edit, more pics at bottom)
02-15-2006, 11:31 PM
#21
5th Gear Member
Join Date: Oct 2004
Location: Orlando, Fl.
Posts: 2,538
RE: Mach 1 Grill delete w/ chin spoiler (edit, more pics at bottom)
ORIGINAL: tcuallstar
i ordered my delete, spoiler, antenna, bumper inserts, underdrive pullies and countless other things from them and never had a problem
ORIGINAL: 2000GT4.6
I admit it, I shoulda listened to your posts complaining about them before.
Mustang tuning sucks.
ORIGINAL: czwalga00gt
Damn straight...
ORIGINAL: 2000GT4.6
I am kinda pissed at mustangtuning for not sending me the clips. Plus, they were supposed to ship it last week monday, and I didn't get it till today. I have heard alot of bad stuff about mustangtuning, and I am starting to believe it.
I am kinda pissed at mustangtuning for not sending me the clips. Plus, they were supposed to ship it last week monday, and I didn't get it till today. I have heard alot of bad stuff about mustangtuning, and I am starting to believe it.
Damn straight...
Mustang tuning sucks.
J/K I have placed a few orders with them (none within the last 12 months) and I never had an issue either.
02-15-2006, 11:58 PM
#22
6th Gear Member
Thread Starter
Join Date: Jan 2004
Location: United States
Posts: 12,575
RE: Mach 1 Grill delete w/ chin spoiler (edit, more pics at bottom)
ORIGINAL: VARifleman
You could try pulling the curved bottom piece out, measuring the plastic rods and getting the corresponding size washers (will be flanged one way with slits in the flange) to push on there, or you could take two of the plastic screws that they gave you (if you have any left) and drill two holes through that piece and use those to hold it down (make sure that where you're drilling goes into the bumper cover before you drill, I messed up and had to drill 2 sets of 2 holes because of this. I had enough screws and push pins (like the ones holding the hood insulation on) to pull it off without it looking bad though).
You could try pulling the curved bottom piece out, measuring the plastic rods and getting the corresponding size washers (will be flanged one way with slits in the flange) to push on there, or you could take two of the plastic screws that they gave you (if you have any left) and drill two holes through that piece and use those to hold it down (make sure that where you're drilling goes into the bumper cover before you drill, I messed up and had to drill 2 sets of 2 holes because of this. I had enough screws and push pins (like the ones holding the hood insulation on) to pull it off without it looking bad though).
I am gonna stick with the double sided tape. They make stuff like that for automotive, so I should be pretty safe way underneath there.
02-16-2006, 05:53 AM
#23
1st Gear Member
Join Date: May 2005
Location:
Posts: 127
RE: Mach 1 Grill delete w/ chin spoiler (edit, more pics at bottom)
I got mine from Steeda and it came preaffixed with 3M double sided mounting tape, it is on nice and snug. Just pick up some of that tape and it will be fine, make sure it is the 3M kind, others will not bond as strongly as I have read some people complain about when attemting to do the same.
02-16-2006, 08:18 PM
#25
6th Gear Member
Thread Starter
Join Date: Jan 2004
Location: United States
Posts: 12,575
RE: Mach 1 Grill delete w/ chin spoiler (edit, more pics at bottom)
ORIGINAL: MustangMafia
Lookin nice. You went with the 2 piece grill delete?
Lookin nice. You went with the 2 piece grill delete?
Just didn't get any mounting hardware for some reason.
Thread
Thread Starter
Forum
Replies
Last Post
