stock ported heads
11-20-2004, 12:03 PM
#11
3rd Gear Member
Join Date: Nov 2004
Location:
Posts: 807
RE: stock ported heads
ORIGINAL: ohsoquik02
or just start with a set of 351 heads from the 80s. they already have those valves just need a good bit of PP work along with a little milling
or just start with a set of 351 heads from the 80s. they already have those valves just need a good bit of PP work along with a little milling
ORIGINAL: 5.0mustang5speed
the reason i am asking is that . heads are high...i am hoping i can find some good one but if not i will port them...i am pretty good..i have done probaly 10 sets of chevy and fords with good results..i figure i will have 1.94 and 1.60 put in them and new seat for under 250.00 around here..
the reason i am asking is that . heads are high...i am hoping i can find some good one but if not i will port them...i am pretty good..i have done probaly 10 sets of chevy and fords with good results..i figure i will have 1.94 and 1.60 put in them and new seat for under 250.00 around here..
I have ported '74 351w heads and had 1.94/1.60 valves installed.
11-20-2004, 02:38 PM
#12
6th Gear Member
Join Date: Nov 2003
Location: Pittsburgh, PA
Posts: 5,182
RE: stock ported heads
you could of fooled me. i got a mic out and measured a set of DOOE heads from the 80s and they had 1.8 ish valves but the mic could be lying.. dunno you tell it all
ORIGINAL: import slayer
The 1.94/1.60 valves came on the '69-70 351w heads. All years after that had the 1.78/1.45 valves.
I have ported '74 351w heads and had 1.94/1.60 valves installed.
ORIGINAL: ohsoquik02
or just start with a set of 351 heads from the 80s. they already have those valves just need a good bit of PP work along with a little milling
or just start with a set of 351 heads from the 80s. they already have those valves just need a good bit of PP work along with a little milling
ORIGINAL: 5.0mustang5speed
the reason i am asking is that . heads are high...i am hoping i can find some good one but if not i will port them...i am pretty good..i have done probaly 10 sets of chevy and fords with good results..i figure i will have 1.94 and 1.60 put in them and new seat for under 250.00 around here..
the reason i am asking is that . heads are high...i am hoping i can find some good one but if not i will port them...i am pretty good..i have done probaly 10 sets of chevy and fords with good results..i figure i will have 1.94 and 1.60 put in them and new seat for under 250.00 around here..
I have ported '74 351w heads and had 1.94/1.60 valves installed.
11-20-2004, 09:44 PM
#14
6th Gear Member
Join Date: Nov 2003
Location: Pittsburgh, PA
Posts: 5,182
RE: stock ported heads
all good man all good
ORIGINAL: import slayer
Oh..I'm sorry, your are right. The 80's had the 1.84/1.50 valves.
It was the 69-70 heads that had original 1.94/1.60
Sorry about the confusion.
Oh..I'm sorry, your are right. The 80's had the 1.84/1.50 valves.
It was the 69-70 heads that had original 1.94/1.60
Sorry about the confusion.
Thread
Thread Starter
Forum
Replies
Last Post
TfcCDR
V6 (1994-2004) Mustangs
1
09-14-2015 12:08 PM
kawiguy827
5.0L GT S550 Tech
0
09-01-2015 07:09 PM
