Since everybody else is doing it......
#1
Since everybody else is doing it......
What kind of times (1/8 and 1/4) do you think I could turn?
B cam
1 5/8" equals
o/r h
flows
cai
C&L iinlet
75mm MAF
70mm TB
underdrives
3.08s (yeah, I know)
OK. Now, what do you think I'd run with the 100 shot of juice?
Remeber, all of this will be on street tires right now. I have plans for DRs in the next llittle bit though. There are several other little mods, but I can't think of them right now, so they probably don't make that much of a power difference.
I'm not a noob and I have an idea of what I should be able to turn, but I thought I would get some of you guys opinions. [&:][&:]
B cam
1 5/8" equals
o/r h
flows
cai
C&L iinlet
75mm MAF
70mm TB
underdrives
3.08s (yeah, I know)
OK. Now, what do you think I'd run with the 100 shot of juice?
Remeber, all of this will be on street tires right now. I have plans for DRs in the next llittle bit though. There are several other little mods, but I can't think of them right now, so they probably don't make that much of a power difference.
I'm not a noob and I have an idea of what I should be able to turn, but I thought I would get some of you guys opinions. [&:][&:]
#2
RE: Since everybody else is doing it......
low 14's, high 13's in the 1/4 mile without the bottle. that's probably mid 9's in the 1/8 mile.
don't have a clue what the 100 HP shot of NOS will do for it, depends a lot on traction and gears and you ain' got either one looks like!
don't have a clue what the 100 HP shot of NOS will do for it, depends a lot on traction and gears and you ain' got either one looks like!
#4
RE: Since everybody else is doing it......
my buddy had a similar setup. Only he was carbed and he ran approx 8.60 in the 1/8th on street tires, not too shabby! Do u have 1.7 rollers w/ that B-CAM. They work well if u dont. I have some I'll sell ya, pm me if interested.
#5
RE: Since everybody else is doing it......
I have stock rockers right now. I might hit you up for those 1.7s at a later datem if you still have them.
Hard to believe, but I actually saw this car go 8.92 in the 1/8th with only CAI, underdrives, and 3.73s. I'll be getting a brand new set of FRPP 3.73s soon from a buddy of mine for $80. Then I get them installed well before the track get going again. I personally think I can get high 12s out of it with the 100 shot.
Hard to believe, but I actually saw this car go 8.92 in the 1/8th with only CAI, underdrives, and 3.73s. I'll be getting a brand new set of FRPP 3.73s soon from a buddy of mine for $80. Then I get them installed well before the track get going again. I personally think I can get high 12s out of it with the 100 shot.
#8
RE: Since everybody else is doing it......
Well with a "similar" setup on street tires I could nab a low 13
13.009 or something close to that.
Had 4.10's and an aftermarket intake manifold.
Was trapping around 112 but bouncing off rev limiter.
And that was on street tires.
But if I were to up that shot once more, I know I could break 11's...
With a warm bottle and my sticky tires.
I am very confident in that.
13.009 or something close to that.
Had 4.10's and an aftermarket intake manifold.
Was trapping around 112 but bouncing off rev limiter.
And that was on street tires.
But if I were to up that shot once more, I know I could break 11's...
With a warm bottle and my sticky tires.
I am very confident in that.
#9
RE: Since everybody else is doing it......
What are you putting down to the wheels on the 75 shot? I pretty much have all of the same engine mods as you, except fot the intake manifold.
Thread
Thread Starter
Forum
Replies
Last Post
stereodesigner
5.0L (1979-1995) Mustang
5
06-22-2011 04:56 PM
Randys66gt
Classic Mustang General Discussion
16
09-19-2010 11:00 PM