possible new motor wondering what you guys think about it and what it should run - MustangForums.com

Go Back  MustangForums.com > Ford Mustang Tech > 5.0L (1979-1995) Mustang > 5.0L General Discussion
Reload this Page >

possible new motor wondering what you guys think about it and what it should run

Notices
5.0L General Discussion This section is for non-tech specific information pertaining to 5.0L Mustangs.

possible new motor wondering what you guys think about it and what it should run

Reply

 
 
 
Old 08-01-2010, 06:17 PM
  #1  
5.0kid
5th Gear Member
Thread Starter
 
5.0kid's Avatar
 
Join Date: Dec 2006
Location: The mitten
Posts: 2,525
Default possible new motor wondering what you guys think about it and what it should run

8.700 DH SVO m-6010-s302 4 bolt center three mains, 1/2 main bolts, 1/2 head bolts.
Scat Billet 4340 3.550 stroke. std./ std.
Crower 5.400 Billet I beam rods 7/16 bolts
wiseco 4.155 bore custom nitrous pistons. .180 wall tapper pins .043/ 1/16/ 3mm heil fire ring set
Cam motion 2.051 roller cam bearing. 276/288 @.050, 114 Lobe sep. .431/ .421 lobe lift .732/.715 with 1.7 rockers 110.25 intake centerline.
Piston to valve. int. .145 .exh. 125
valve lash .020 cold .024 hot
ring gaps .026
JP performance billet double roller/ double doweled 7/16 cam bolt. timing chain set.
summit sfi racing balancer.
comp. cams roller thrust cam plate.
crower severe duty .874 roller lifters with pressure oiling hole

Heads:
twisted wedge r series. fully ported. 1262R intake size.
2.125/ 1.625 ferrea stainless valves (new), Manley titan. 10 degree retainers, manley 221425-16 double nextex drag springs (new), springs installed 2.010 installed height 340 lbs seat/ 840 lbs @ .800 lift, coil bind 1.150
head flow 343 @ .650 lift intake 259 @ .700 lift exhaust no pipe 28 "

Misc.
canton 13-622 pro series oil ban, has moroso oil preheating pad for spring/ fall cold weather. 7/8 special pick up.
melling racing 10687 std. volume racing oil pump. saftey wired bolts. ford racing drive shaft.
7 qts pennzoil 15w 40 oil primed 55 psi, fram racing hp1 oil filter.
Edelbrock 8.700 super victor intake. ported. rear water lines.
MSD locked distributor, Bronze gear. Fire core custom made wires, autolite racing sparkplugs. set timing 32- 34 degrees total.
Sheet metal valve covers with -12 an fitting for vacume pump.
all parts magnaflexed before assembly.
.0020/ .0022 main bearing clearance, .0025/ .0027 rod bearing clearance.
coated polmer dynamics/ clevite h series bearings.
mls fel-pro head gaskets.
crower stainless steel enduro 1.7 rocker arms.
Probe stud girdle.
trend 3/8 .135 wall push-rods.
shift point 7600-7800 rpm, 8200 max.
.085 oil restictors installed in block.
one spare new piston included.
torque mains inner 100 ftlbs/ outer 45 ftlbs moly lube.
torque rods 70 ftlbs with lube.
torque heads 100 ftlbs moly lube.

im thinking on a 200 shot should be good into the 8s
5.0kid is offline  
Reply With Quote
Old 08-01-2010, 08:37 PM
  #2  
TrimDrip
5th Gear Member
 
TrimDrip's Avatar
 
Join Date: Jan 2009
Location: AL
Posts: 2,816
Default

ah maybe, if the car was lighter than 3200 pounds I would defiantly think so.
TrimDrip is online now  
Reply With Quote
Old 08-01-2010, 08:43 PM
  #3  
5.0kid
5th Gear Member
Thread Starter
 
5.0kid's Avatar
 
Join Date: Dec 2006
Location: The mitten
Posts: 2,525
Default

3154 with me in it
5.0kid is offline  
Reply With Quote
Old 08-01-2010, 09:13 PM
  #4  
TrimDrip
5th Gear Member
 
TrimDrip's Avatar
 
Join Date: Jan 2009
Location: AL
Posts: 2,816
Default

for some reason, i read the weight wrong the first time. Yeah, I think it could hit the eights. If it didn't, you cold always run a shot to get you going then a fogger set-up to get you down the track.

Are you going to go change the transmission to a powerglide or keep the 3 speed?
TrimDrip is online now  
Reply With Quote
Old 08-01-2010, 11:16 PM
  #5  
mjr46
D.R. THE PATHETIC DORK
 
mjr46's Avatar
 
Join Date: Jun 2007
Location: West Virginia
Posts: 30,809
Default

sounds like alot more money you'd have to dump into to your ride to make it certifiable to run down into that range, if the pockets are deep, go for it
mjr46 is offline  
Reply With Quote
Old 08-02-2010, 01:16 AM
  #6  
5.0kid
5th Gear Member
Thread Starter
 
5.0kid's Avatar
 
Join Date: Dec 2006
Location: The mitten
Posts: 2,525
Default

Originally Posted by mjr46 View Post
sounds like alot more money you'd have to dump into to your ride to make it certifiable to run down into that range, if the pockets are deep, go for it
shouldnt be too much just finish the 10 pt and then some other saftey things nothing major i dont think. and yeah time drip i was thinking of a plate with a fogger also
5.0kid is offline  
Reply With Quote
Old 08-02-2010, 01:17 AM
  #7  
5.0kid
5th Gear Member
Thread Starter
 
5.0kid's Avatar
 
Join Date: Dec 2006
Location: The mitten
Posts: 2,525
Default

Originally Posted by TrimDrip View Post
for some reason, i read the weight wrong the first time. Yeah, I think it could hit the eights. If it didn't, you cold always run a shot to get you going then a fogger set-up to get you down the track.

Are you going to go change the transmission to a powerglide or keep the 3 speed?
prob keep the 3 speed for now just cus its gonna have a better 60' with the shorter 1st gear will have to send in to be built up though
5.0kid is offline  
Reply With Quote
Old 08-02-2010, 02:17 AM
  #8  
w8less
6th Gear Member
 
w8less's Avatar
 
Join Date: Feb 2005
Location: KY
Posts: 13,398
Default

you find out the bore? when you going to put that car on a real diet?
w8less is offline  
Reply With Quote
Old 08-02-2010, 11:29 AM
  #9  
5.0kid
5th Gear Member
Thread Starter
 
5.0kid's Avatar
 
Join Date: Dec 2006
Location: The mitten
Posts: 2,525
Default

Originally Posted by fs308 View Post
you find out the bore? when you going to put that car on a real diet?
still calling frpp at the moment trying to get an answer
5.0kid is offline  
Reply With Quote
Old 08-02-2010, 11:31 AM
  #10  
kweb288
5th Gear Member
 
kweb288's Avatar
 
Join Date: Feb 2007
Location: St. Charles Il, and ISU
Posts: 3,736
Default

that sounds like a decent engine

did you get your cage certified yet?
kweb288 is offline  
Reply With Quote

Thread Tools
Search this Thread
Quick Reply: possible new motor wondering what you guys think about it and what it should run


Advertising
Featured Sponsors
Vendor Directory

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.