tremec 3550 crossmember??? - MustangForums.com


5.0L General Discussion This section is for non-tech specific information pertaining to 5.0L Mustangs.

Reply
 
 
 
Thread Tools Search this Thread
Old 08-30-2010, 04:14 PM   #1  
mjr46
D.R. THE PATHETIC DORK
Thread Starter
 
mjr46's Avatar
 
Join Date: Jun 2007
Location: West Virginia
Posts: 30,802
Default tremec 3550 crossmember???

So I had a few free minutes before work ended and I installed the bellhousing and threw the tranny up in there and when i WENT TO INSTALL THE stock t-5 crossmember, it is not gonna line up unless you cut the welds and slide the crossmember back on the tubes....Just wondering what you tremec owners have done to resolve the issue???, I'd rather not hack up the stock crossmember in case I put a t-5 back in later if I sell the car.......also can you use the stock style trans mount?? mine is a energy suspension poly one for a t-5.
mjr46 is offline   Reply With Quote
Old 08-30-2010, 04:38 PM   #2  
ctgreddy
6th Gear Member
 
Join Date: May 2007
Location: Dearborn, MI
Posts: 6,277
Default

I used my stock mount and my stock crossmember. I did not use the little adapter plate the t5's use tho. but i'm not sure if my sn crossmember is different than a fox's. also make sure you get the steeda d/s spacer.
ctgreddy is offline   Reply With Quote
Old 08-30-2010, 05:24 PM   #3  
AdderMk2
Banned
 
Join Date: Dec 2005
Location: Lil' Rhody
Posts: 22,376
Default

Quote:
Originally Posted by ctgreddy View Post
I used my stock mount and my stock crossmember. I did not use the little adapter plate the t5's use tho. but i'm not sure if my sn crossmember is different than a fox's. also make sure you get the steeda d/s spacer.
you should have used the adapter plate.


Mike, you need to either cut the welds, or purchase http://www.summitracing.com/parts/FMS-M-5059-A/
AdderMk2 is offline   Reply With Quote
Old 08-30-2010, 06:09 PM   #4  
ctgreddy
6th Gear Member
 
Join Date: May 2007
Location: Dearborn, MI
Posts: 6,277
Default

i tried using the adapter plate. wouldn't work in my car, not sure why but nothing was even close to lining up with it in there.
ctgreddy is offline   Reply With Quote
Old 08-30-2010, 07:09 PM   #5  
mjr46
D.R. THE PATHETIC DORK
Thread Starter
 
mjr46's Avatar
 
Join Date: Jun 2007
Location: West Virginia
Posts: 30,802
Default

Quote:
Originally Posted by ctgreddy View Post
I used my stock mount and my stock crossmember. I did not use the little adapter plate the t5's use tho. but i'm not sure if my sn crossmember is different than a fox's. also make sure you get the steeda d/s spacer.
I don't think foxbodies need to use a drive shaft spacer, that is only for sn-95's I think due to the fact they are a tad longer , but I could be wrong
mjr46 is offline   Reply With Quote
Old 08-30-2010, 07:13 PM   #6  
mjr46
D.R. THE PATHETIC DORK
Thread Starter
 
mjr46's Avatar
 
Join Date: Jun 2007
Location: West Virginia
Posts: 30,802
Default

Quote:
Originally Posted by AdderMk2 View Post
you should have used the adapter plate.


Mike, you need to either cut the welds, or purchase http://www.summitracing.com/parts/FMS-M-5059-A/
I figured as much, guess I'll just get the one from the link you posted........for a fox the driveshaft spacer isn't needed is it???
mjr46 is offline   Reply With Quote
Old 08-30-2010, 07:14 PM   #7  
ctgreddy
6th Gear Member
 
Join Date: May 2007
Location: Dearborn, MI
Posts: 6,277
Default

sn95's and fox's used the same driveshaft. i dont see how fox's could not need the spacer.
ctgreddy is offline   Reply With Quote
Old 08-30-2010, 07:39 PM   #8  
mjr46
D.R. THE PATHETIC DORK
Thread Starter
 
mjr46's Avatar
 
Join Date: Jun 2007
Location: West Virginia
Posts: 30,802
Default

^^^I'll have to look into that then
mjr46 is offline   Reply With Quote
Old 08-30-2010, 07:51 PM   #9  
AdderMk2
Banned
 
Join Date: Dec 2005
Location: Lil' Rhody
Posts: 22,376
Default

fox doesnt need the spacer
AdderMk2 is offline   Reply With Quote
Old 08-30-2010, 07:54 PM   #10  
ctgreddy
6th Gear Member
 
Join Date: May 2007
Location: Dearborn, MI
Posts: 6,277
Default

Quote:
Originally Posted by AdderMk2 View Post
fox doesnt need the spacer
what's the difference? I'm not doubting you at all i'm just wondering.
ctgreddy is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
2002 Mustang GT Premium 5 Speed JonnyBlazeGT Mustangs For Sale 3 11-03-2015 01:10 AM
god help me. I need a bellhousing for a tr3650 Jskeezy84 4.6L General Discussion 5 09-08-2015 01:40 AM
T56 Spline Shafts NOW IN STOCK @ LethalPerformance.com! Boostaddict Lethal Performance 0 08-13-2015 01:57 PM
Overheating problem! kubskrew 5.0L (1979-1995) Mustang 13 08-13-2004 10:13 PM
Parts for 3550 tremec transmission 93stang 5.0L (1979-1995) Mustang 1 05-18-2004 08:17 PM


Tags
3550, 50, 95, adapter, body, crossmember, fox, foxbody, hpm, install, mounts, mustang, stock, tko, trans, tremec, tremmec

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump

Advertising
Featured Sponsors
Vendor Directory

All times are GMT -5. The time now is 04:37 AM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.