Audio/Visual Electronics Wired up? Everyone's got some sort of electrical modification... let's hear about it here.

Shaker 500 Removal

Thread Tools
 
Search this Thread
 
Old 10-20-2005, 10:50 AM
  #1  
JJ_Stang
2nd Gear Member
Thread Starter
 
JJ_Stang's Avatar
 
Join Date: Sep 2005
Location: Stamford, CT
Posts: 354
Default Shaker 500 Removal

I am in the process of elimination the Skipper 500, does anyone know if their is an amp/amps that powers the 8' subs in the door? If so where is it? Head Unit replacement was not hard at all, Rear deck speaker replacement easy, was hoping to do the doors this weekend but its gonna rain. Any Idea's or thoughts.

Thanks,
Jeff
JJ_Stang is offline  
Old 10-21-2005, 11:59 PM
  #2  
fso119
2nd Gear Member
 
fso119's Avatar
 
Join Date: Sep 2005
Location:
Posts: 167
Default RE: Shaker 500 Removal

ORIGINAL: JJ_Stang

I am in the process of elimination the Skipper 500, does anyone know if their is an amp/amps that powers the 8' subs in the door? If so where is it? Head Unit replacement was not hard at all, Rear deck speaker replacement easy, was hoping to do the doors this weekend but its gonna rain. Any Idea's or thoughts.

Thanks,
Jeff
I just replaced my Shaker 500 with a Pioneer DEH-P3700MP. Sounds great with the factory amp. They used a special harness to hookup the amp to the head unit($20) The amp should be somewhere on the left side(on V6) or right side(on GT) of the head unit from I saw somewhere on this forum. The amp powers all the speakers.
fso119 is offline  
Old 11-01-2005, 01:12 PM
  #3  
millergt
1st Gear Member
 
millergt's Avatar
 
Join Date: Sep 2005
Posts: 113
Default RE: Shaker 500 Removal

What is the trick to pulling out the shaker 500 head unit?
millergt is offline  
Old 11-01-2005, 08:02 PM
  #4  
JJ_Stang
2nd Gear Member
Thread Starter
 
JJ_Stang's Avatar
 
Join Date: Sep 2005
Location: Stamford, CT
Posts: 354
Default RE: Shaker 500 Removal


1. Open the armrest and remove the 2 screws all the way towards the rear of the car.
2. Unscrew the shift ****
3. Remove the whole unit be careful getting the piece around the emergency brake I think their are 4 body clips
4. you now need to pull out the 2 side pieces, where your knee rests wile driving, they should just pop right out
5. Their are 6 9/32nd screws holding the climate control unit once the unit is free you can pull it out a little and then disconnect all the cables from the back of all the controls, one of them has a grey lever that you have to push and then pull. The lighter is also a pin to disconnect
6. then their are 4 9/32nd screws that hold the radio, their are 3 connectors in the back + the antenna. Putting the Shifter in reverse gives you a little more clearance.

Hope this helps I knew I should of took some pics.

JJ_Stang is offline  
Old 11-20-2005, 12:05 PM
  #5  
gamoon
 
gamoon's Avatar
 
Join Date: Nov 2005
Posts: 2
Default RE: Shaker 500 Removal

JJ_Stang those were very good instructions but I could not remove the connector that you state "one of them has a grey lever that you have to push and then pull". I tried pushing, pulling etc but I could not get it to come out.
gamoon is offline  
Old 11-22-2005, 10:12 PM
  #6  
BigFloppy
2nd Gear Member
 
BigFloppy's Avatar
 
Join Date: Nov 2005
Location: Marietta, GA
Posts: 307
Default RE: Shaker 500 Removal

FORCE the lever to the down position (there's actuallt 2 of them) if you want to release the whole front plate. Both operate the same way (it's likey that the grey lever will "break") NO WORRIES, the installer guy broke mine as well first time he worked on it

The lever basically unlocks the connector
BigFloppy is offline  
Old 11-23-2005, 01:46 PM
  #7  
hawgman
I ♥ Acer
 
hawgman's Avatar
 
Join Date: Feb 2005
Location: Texas
Posts: 3,225
Default RE: Shaker 500 Removal


ORIGINAL: fso119

I just replaced my Shaker 500 with a Pioneer DEH-P3700MP. Sounds great with the factory amp. They used a special harness to hookup the amp to the head unit($20) The amp should be somewhere on the left side(on V6) or right side(on GT) of the head unit from I saw somewhere on this forum. The amp powers all the speakers.
The amps are on the drivers side on GTs also. And just FYI, the head unit powers the door and deck lid speakers. Amps only power the subs.
hawgman is offline  
Old 04-25-2006, 09:44 AM
  #8  
StangManFla
 
StangManFla's Avatar
 
Join Date: Feb 2006
Posts: 13
Default RE: Shaker 500 Removal

Do the Amps power anything but the subs? I've talked to a few people who advised me to be careful... they think the amps may be used for power features i.e... power seat, air bags, door locks. Is this true or can i remove the amps with no problems?
StangManFla is offline  
Old 04-25-2006, 02:31 PM
  #9  
JJ_Stang
2nd Gear Member
Thread Starter
 
JJ_Stang's Avatar
 
Join Date: Sep 2005
Location: Stamford, CT
Posts: 354
Default RE: Shaker 500 Removal

The amps only power the subs, you can easily remove them.
JJ_Stang is offline  
Old 04-28-2006, 02:32 PM
  #10  
schmecky
1st Gear Member
 
schmecky's Avatar
 
Join Date: Mar 2006
Location:
Posts: 62
Default RE: Shaker 500 Removal

yes the amps are in the driver's kick panel and can be removed without causing problems....mine have unhooked for a month and no problems they just power the 8's in the doors...
schmecky is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
BOB ROME
5.0L (1979-1995) Mustang
3
07-26-2023 01:54 PM
jwog666
Pipes, Boost & Juice
11
12-27-2021 08:09 PM
Dathan
V6 (1994-2004) Mustangs
4
10-05-2015 05:52 AM
jrrhd73must
Classic Mustang General Discussion
2
10-02-2015 09:17 PM
nmra1965
Other Professional Racing
0
09-26-2015 10:46 AM



Quick Reply: Shaker 500 Removal



All times are GMT -5. The time now is 04:04 PM.