Magnaflow exhaust dyno sheets
#1
Magnaflow exhaust dyno sheets
2003 Cobra! Mods: Steeda cold air, Magnaflow exhaust (mufflers & piping only)</P>
<TABLE cellSpacing=2 cellPadding=4 width="100%">
<T>
<TR class=smalltext>
<TD class=smalltextbold>Engine Specs:</TD>
<TD class=smalltext>4.6Liter dohc (8Cyl)</TD></TR>
<TR>
<TD class=smalltextgraybold>Mileage:</TD>
<TD class=smalltextgray>4000 miles</TD></TR>
<TR>
<TD class=smalltextbold>Aspiration:</TD>
<TD class=smalltext>super-charged[8 psi]</TD></TR>
<TR>
<TD class=smalltextgraybold height=19>Transmission:</TD>
<TD class=smalltextgray>6M</TD></TR>
<TR>
<TD class=smalltextbold>Max RWHP:</TD>
<TD class=smalltext>404.1 @ 6400 rpms</TD></TR>
<TR class=smalltext>
<TD class=smalltextgraybold>Max RWTQ:</TD>
<TD class=smalltextgray>368.1 @ 4380 rpms</TD></TR>
<TR>
<TD class=smalltextbold>Estimated Fly Wheel Horsepower:</TD>
<TD class=smalltext>481 @ 6400 rpms [assuming 16 % drivetrain loss]</TD></TR>
<TR>
<TD class=smalltextgraybold>Estimated Fly Wheel Torque:</TD>
<TD class=smalltextgray>438 @ 4380 rpms [assuming 16 % drivetrain loss]</TD></TR>
<TR>
<TD class=smalltextbold>Room temp / Inlet Temp (F):</TD>
<TD class=smalltext>0.0 / 69.3</TD></TR>
<TR>
<TD class=smalltextgraybold>Pressure (kPa):</TD>
<TD class=smalltextgray>30.0</TD></TR>
<TR>
<TD class=smalltextbold>Humidity (%):</TD>
<TD class=smalltext>0.0</TD></TR>
<TR>
<TD class=smalltextgraybold vAlign=top>Condition Details:</TD>
<TD class=smalltextgray>Gear Ratio : 49.34 RPM/MPH Correction Factor : 0.96 SAE </TD></TR>
<TR>
<TD class=smalltextbold vAlign=top>Notes:</TD>
<TD class=error></TD></TR>
<TR>
<TD class=smalltextgraybold vAlign=top>Fan:</TD>
<TD class=smalltextgray>off</TD></TR>
<TR>
<TD class=smalltextbold vAlign=top>Date and Time:</TD>
<TD class=smalltext>2003-04-05 - 13:03:32</TD></TR>
<TR class=smalltextgray>
<TD class=smalltextbold>
<P align=left>Dyno Correction Factor </P></TD>
<TD class=smalltextgray>
SAE Corrected </P>
<P align=center></P>
<P align=left></P>
**According to this site**</P>
</P>
350hp stock, Magnaflow exhaust with Steeda CAI 404hp. </P>
**Quote from site**</P>
Another bone-stock '03 Cobra was there, and posted numbers of Power 350.6 and Torque 358.8. Interestingly enough, Bassani x and cats added 20.2 hp and 9 to torque for him. </P>
I'd say Magnaflow won..by A LOT!</P>
<P align=left></P></TD></TR></T></TABLE></P>
#2
Magnaflow exhaust dyno sheets
*Other dyno results from another webpage*</P>
<FONT size=2>Now Matt's new Cobra was no slouch, it slapped down 389 hp and 372 ft lbs of torque on it's first run. The second run he ran 386 hp and 369 ft lbs of torque. This is pretty much standard for a stock 2003 Cobra with a Flowmaster catback system & CAI.</FONT></P>
Thread
Thread Starter
Forum
Replies
Last Post
junior04
4.6L (1996-2004 Modular) Mustang
1
09-28-2015 10:53 AM
tj@steeda
Steeda Autosports
0
09-24-2015 09:18 PM