J&M Panhard Bar Installed - MustangForums.com

Notices
S197 Handling Section For everything suspension related, inlcuding brakes, tires, and wheels.

J&M Panhard Bar Installed

Reply

 
 
 
Old 09-15-2018, 05:34 PM
  #1  
08'MustangDude
4th Gear Member
Thread Starter
 
Join Date: Jan 2018
Location: Pennsylvania
Posts: 1,322
Default J&M Panhard Bar Installed

Pics should tell the story, no need to describe everything:
OE
OE
OE -vs- J&M
OE -vs- J&M
OE -vs- J&M
J&M Installed



Zerk
Zerk
08'MustangDude is offline  
Reply With Quote
Old 09-17-2018, 06:30 AM
  #2  
Norm Peterson
6th Gear Member
 
Norm Peterson's Avatar
 
Join Date: Feb 2007
Location: state of confusion
Posts: 7,499
Default

Before bolting this part up, did you make sure that the metal inner sleeves in the new PHB bushings were ever so slightly longer than the bushing material itself?


Norm
Norm Peterson is offline  
Reply With Quote
Old 09-17-2018, 06:38 AM
  #3  
GT Nate
2nd Gear Member
 
GT Nate's Avatar
 
Join Date: Dec 2017
Location: Missouri
Posts: 310
Default

I did the same with mine... my old bar was pretty rusty... the new one made all the difference.
GT Nate is offline  
Reply With Quote
Old 09-17-2018, 01:12 PM
  #4  
08'MustangDude
4th Gear Member
Thread Starter
 
Join Date: Jan 2018
Location: Pennsylvania
Posts: 1,322
Default

Originally Posted by Norm Peterson View Post
Before bolting this part up, did you make sure that the metal inner sleeves in the new PHB bushings were ever so slightly longer than the bushing material itself?
Norm
Nope, and as I said in the other thread, their product pictures don't show it slightly longer either.
I think they were dead even, but I put grease in them before putting them on, and the one bushing
pushed out a little. When I tightened it, grease came out the Zerk fitting... I am not concerned,
it will be fine. It is not a daily driver...


08'MustangDude is offline  
Reply With Quote
Old Yesterday, 03:42 AM
  #5  
08'MustangDude
4th Gear Member
Thread Starter
 
Join Date: Jan 2018
Location: Pennsylvania
Posts: 1,322
Default

As for putting in the UCA, do you have to remove the bolts from the bracket to install
just the UCA arm? Almost every video I saw, shows pulling the bolts out; one from under
the rear seat, and the two from the bottom. They put the arm in, snug those bushing
bolts, then put the bracket bolts back in, tighten to spec, then tighten the two bushing
UCA bolts to spec.

Just wondering, why can't you just replace the arm, without doing anything with the
bracket?
08'MustangDude is offline  
Reply With Quote
Old Yesterday, 06:56 AM
  #6  
Norm Peterson
6th Gear Member
 
Norm Peterson's Avatar
 
Join Date: Feb 2007
Location: state of confusion
Posts: 7,499
Default

If you're only replacing a short (2005-2010) OE arm with an aftermarket arm of the same length, you don't need to replace the bracket.

It's when you put the later (2011-up) longer arm into a car that came with the short arm to get the benefit the extra length has on the geometry that you must replace the bracket.

You might want to replace the bracket with a multi-hole short arm bracket for use with an existing short arm if you were thinking about trying out different UCA inclinations for IC location/anti-squat dragstrip reasons and weren't going to go with the long arm. Though it seems to me if you were going to go to that much trouble you might as well go with the longer arm and do it all up in one shot.

There's no good reason to put a short arm in a later car that came with the long arm as OE.

Norm
Norm Peterson is offline  
Reply With Quote
Old Yesterday, 11:41 AM
  #7  
08'MustangDude
4th Gear Member
Thread Starter
 
Join Date: Jan 2018
Location: Pennsylvania
Posts: 1,322
Default

Originally Posted by Me
As for putting in the UCA, do you have to remove the bolts from the bracket to install
just the UCA arm?
Almost every video I saw, shows pulling the bolts out; one from under
the rear seat, and the two from the bottom. They put the arm in, snug those bushing
bolts, then put the bracket bolts back in, tighten to spec, then tighten the two bushing
UCA bolts to spec.

Just wondering, why can't you just replace the arm, without doing anything with the
bracket?
So, yeah, I don't have a bracket, never had a bracket, I didn't ask about replacing the bracket. I
asked if I really have to loosen the bracket to put the J&M UCA in. The arm is just to replace the
factory arm, nothing about longer, nothing about shorter; I just asked about having to loosen up the
bracket to replace the UCA... It's almost a YES or NO question...
08'MustangDude is offline  
Reply With Quote
Old Yesterday, 02:53 PM
  #8  
Norm Peterson
6th Gear Member
 
Norm Peterson's Avatar
 
Join Date: Feb 2007
Location: state of confusion
Posts: 7,499
Default

It might be a matter of not being able to access the pivot bolt well enough to properly torque it. The factory shop manual specifically calls for removing the bracket when removing the arm, and mentions that the fuel tank needs to be dropped slightly as part of this removal procedure.


Norm
Norm Peterson is offline  
Reply With Quote
Old Yesterday, 05:43 PM
  #9  
08'MustangDude
4th Gear Member
Thread Starter
 
Join Date: Jan 2018
Location: Pennsylvania
Posts: 1,322
Default

Okay, all the videos show not touching the fuel tank, but taking the
two underside bolts out of the bracket, with real long extensions, and
one inside under the seats. I'm probably not going to go through all
of that, so will probably just toss the UCA in the trash. Not worth
selling for what I paid for it, and shipping on top of it... Just don't see
it being a big improvement for all that work...
08'MustangDude is offline  
Reply With Quote
Reply
 
 
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
audioAl
S197 Handling Section
2
02-08-2013 04:09 PM
flolo
Parts For Sale
6
04-14-2010 08:48 AM

Forum Jump

Thread Tools
Search this Thread
Advertising
Featured Sponsors
Vendor Directory