MustangForums.com - Search Results



Showing results 1 to 25 of 500
Search took 0.30 seconds.
Search: Posts Made By: yurizx6r
Forum: 5.0L (1979-1995) Mustang 03-31-2017, 06:06 AM
Replies: 19
Views: 693
Posted By yurizx6r
After REALLY looking at my setup, I’ve come to...

After REALLY looking at my setup, I’ve come to the conclusion that it would look like complete crap if I cut the fenders unless I had Chip Foose do it. My hand isn’t that steady, I don’t trust...
Forum: 5.0L (1979-1995) Mustang 03-27-2017, 04:03 PM
Replies: 19
Views: 693
Posted By yurizx6r
Both wheels are spinning. I just verified it a...

Both wheels are spinning. I just verified it a few days ago.
Forum: 5.0L (1979-1995) Mustang 03-21-2017, 07:04 PM
Replies: 15
Views: 536
Posted By yurizx6r
Ok. Just making sure it wasn't an ignition issue....

Ok. Just making sure it wasn't an ignition issue. It's not popping under WOT right? It's tuned correctly and all that? Either way good job getting a Motorcraft IAC. Can't beat OEM on some things.
Forum: 5.0L (1979-1995) Mustang 03-21-2017, 06:01 PM
Replies: 15
Views: 536
Posted By yurizx6r
Hey sorry, but I didn't see your original thread....

Hey sorry, but I didn't see your original thread. What's the overall problem? Also, did you do a base idle reset with the car warm?
Forum: 5.0L (1979-1995) Mustang 03-20-2017, 07:04 PM
Replies: 15
Views: 536
Posted By yurizx6r
Spend the money on a Motorcraft IAC. Those cars...

Spend the money on a Motorcraft IAC. Those cars are notorious for bad IACs. I've tried a few BWD ones (all junk) that lasted a few months, tried a Duralast one which seemed ok, but finally spent the...
Forum: 5.0L (1979-1995) Mustang 03-16-2017, 09:10 AM
Replies: 19
Views: 693
Posted By yurizx6r
@Boss Hotrod: That's cool. I'm probably going to...

@Boss Hotrod: That's cool. I'm probably going to eventually put it on either way just because.... race car. lol But, I wanted to figure out this underline issue first. My camshaft calls for a MINIMUM...
Forum: 5.0L (1979-1995) Mustang 03-16-2017, 07:32 AM
Replies: 19
Views: 693
Posted By yurizx6r
Got yah. These responses were not what I...

Got yah. These responses were not what I expected, but certainly appreciate them. I guess I'll have to really find a place to practice more to figure out the limitations of the new power I have while...
Forum: 5.0L (1979-1995) Mustang 03-15-2017, 12:44 PM
Replies: 19
Views: 693
Posted By yurizx6r
It is true that I need a little more experience...

It is true that I need a little more experience learning how to correct it when the rear end loses control, but there's no place to really practice that where I live. It's a pretty heavily populated...
Forum: 5.0L (1979-1995) Mustang 03-15-2017, 05:08 AM
Replies: 6
Views: 518
Posted By yurizx6r
The car was designed to run copper top plugs, so...

The car was designed to run copper top plugs, so I just use MGK copper tops with Ford Racing wires. However, you will not notice any difference until you put in a MSD ignition box like a 6AL. That's...
Forum: 5.0L (1979-1995) Mustang 03-14-2017, 05:34 PM
Replies: 19
Views: 693
Posted By yurizx6r
My #1 goal is to keep it straight if the tires...

My #1 goal is to keep it straight if the tires spin. I don't care if the spin, just don't fishtail or over steer on me. I've seen too many stangs on medians to not take that seriously. Without a dyno...
Forum: 5.0L (1979-1995) Mustang 03-13-2017, 04:33 PM
Replies: 19
Views: 693
Posted By yurizx6r
Maximum Motorsports Panhard Bar

Hey guys,

I was wondering if anybody has installed a MM panhard bar. What I would really like to know is two things? 1. Do you get a lot of noise inside the car/ does it make it less DD friendly?...
Forum: 5.0L (1979-1995) Mustang 03-13-2017, 04:26 PM
Replies: 9
Views: 476
Posted By yurizx6r
That certainly helps! lol But I would still take...

That certainly helps! lol But I would still take it to a local tuner who can tune YOUR car. Bama will get you moving, but it's not a good tune doing it from another state just taking wild shots and...
Forum: 5.0L (1979-1995) Mustang 03-13-2017, 04:21 PM
Replies: 3
Views: 210
Posted By yurizx6r
I had a similar issue to where my fox wouldn't...

I had a similar issue to where my fox wouldn't start easily. It seemed fine once you got it started, but anything after 3,000 RPMS it would backfire. After checking the fuel pressure, battery, vacuum...
Forum: 5.0L (1979-1995) Mustang 11-11-2016, 11:19 AM
Replies: 8
Views: 285
Posted By yurizx6r
That's the 2nd time MSD has let me down. I bought...

That's the 2nd time MSD has let me down. I bought a MSD distributor and the second I put it in the idle went crazy and kept dying on me (installed it correctly, I've done tones of those). I put the...
Forum: 5.0L (1979-1995) Mustang 11-10-2016, 08:03 PM
Replies: 11
Views: 710
Posted By yurizx6r
Ok. I tried advancing my timing on my chain by 3...

Ok. I tried advancing my timing on my chain by 3 degrees once (YES I DID IT RIGHT, you cant screw it up), turned it by hand to make sure it was good, and then it wouldn't start. I had to play with...
Forum: 5.0L (1979-1995) Mustang 11-10-2016, 03:57 PM
Replies: 11
Views: 710
Posted By yurizx6r
You didn't try to advance or retard the timing on...

You didn't try to advance or retard the timing on the chain did you?
Forum: 5.0L (1979-1995) Mustang 11-10-2016, 03:49 PM
Replies: 8
Views: 285
Posted By yurizx6r
Finally figured it out. It was...

Finally figured it out. It was .................................................. damn MSD ignition coil. Thing was only 3 years old. The IAC helped, but it was still starting slower than usual, then...
Forum: 5.0L (1979-1995) Mustang 11-05-2016, 07:50 AM
Replies: 8
Views: 285
Posted By yurizx6r
Started her up this morning. Pretty normal start,...

Started her up this morning. Pretty normal start, maybe a second longer than usual, but no issues. Idle was good. Right at "1,000" (tuner says it's really 860) where I tuned it to be. I gathered some...
Forum: 5.0L (1979-1995) Mustang 11-04-2016, 07:03 PM
Replies: 8
Views: 285
Posted By yurizx6r
No codes at all. The popping sounded like...

No codes at all. The popping sounded like backfiring from the exhaust. It happened quickly as in 4 start ups were slow and gradually getting slower. I tried switching the IAC today. It started right...
Forum: 5.0L (1979-1995) Mustang 11-04-2016, 06:39 AM
Replies: 8
Views: 285
Posted By yurizx6r
Long starts when cold

Hey guys,

I'm having a problem starting my fox when the car is cold. I live in FL, and it's still above 80 degrees, so it's not a tuning issue with the weather. Once I get it started and the car...
Forum: 5.0L (1979-1995) Mustang 10-27-2015, 06:16 AM
Replies: 12
Views: 640
Posted By yurizx6r
Cool I realize that not everything they sell is good....

I realize that not everything they sell is good. But their impact gun (the Earthquake) is actually fantastic. I've had great success with it. I have also had great success with their ratchets and...
Forum: 5.0L (1979-1995) Mustang 10-16-2015, 06:15 AM
Replies: 12
Views: 640
Posted By yurizx6r
Like mjr46 said, buy ARP bolts. I have them on my...

Like mjr46 said, buy ARP bolts. I have them on my intake (and everything else). Trust me, if you break an ARP bolt........there's a serious problem (YOU). Check your torque wrench too. Harbor freight...
Forum: 5.0L (1979-1995) Mustang 10-12-2015, 09:01 AM
Replies: 18
Views: 690
Posted By yurizx6r
Oh, I didn't know that. I've just seen a few...

Oh, I didn't know that. I've just seen a few articles on it with good hp & torque gains. Good to know!
Forum: 5.0L (1979-1995) Mustang 10-12-2015, 06:11 AM
Replies: 18
Views: 690
Posted By yurizx6r
I would recommend keeping the phenolic spacer...

I would recommend keeping the phenolic spacer though, those do wonders on carburetors. If you ever decide to get a cowl hood or something, slap that baby back on there.
Forum: 5.0L (1979-1995) Mustang 10-06-2015, 08:09 PM
Replies: 18
Views: 690
Posted By yurizx6r
4" is too big IMO. I have a 3"...........hood...

4" is too big IMO. I have a 3"...........hood that is......lol it's good, but I would rather have the 2.5 or 1.5.
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -5. The time now is 08:05 PM.