MustangForums.com - Search Results

Go Back  MustangForums.com > Search Forums
Reload this Page >

Search Results

 
Search: Posts Made By: RUDEDOG.357
Showing results 1 to 25 of 36
Search took 0.15 seconds.
Forum: General Tech
11-29-2009, 11:54 AM
Replies: 5
Views: 2,172
Posted By RUDEDOG.357

If it was a T-5 i would say it was easy. but i...

If it was a T-5 i would say it was easy. but i think your vehicle has the T-45 which you have to split trans to get at the forks.
Forum: General Tech
11-29-2009, 11:41 AM
Replies: 9
Views: 1,097
Posted By RUDEDOG.357

Its probably the alternator. Ive had alternators...

Its probably the alternator. Ive had alternators that charge when you ck them out and then wont. brushes are probably worn out.
10-27-2009, 10:57 PM
Replies: 8
Views: 421
Posted By RUDEDOG.357

I installed a 75mm edelbrock tbody on my 89 stang...

I installed a 75mm edelbrock tbody on my 89 stang and i think it killed some throttle response. I have 30 lb injectors with edelbrock heads and intake. I would stay with 65 or 70mm.
10-27-2009, 10:52 PM
Replies: 15
Views: 607
Posted By RUDEDOG.357

ck the pinion flange and see if it is loose or...

ck the pinion flange and see if it is loose or damaged. they may have not tightened the pinion enough.
09-19-2009, 09:02 PM
Replies: 5
Views: 310
Posted By RUDEDOG.357

Did you seal the threads on the water pump bolts....

Did you seal the threads on the water pump bolts. some go into coolant. if you dont coolant will get past the bolts.
09-19-2009, 08:37 PM
Replies: 12
Views: 1,449
Posted By RUDEDOG.357

sounds like you a/c is icing up. its probably the...

sounds like you a/c is icing up. its probably the low pressure switch not cutting out the a/c compressor when the pressure gets low. next time you start your car with the a/c ck that the compressor...
09-19-2009, 08:11 PM
Replies: 2
Views: 765
Posted By RUDEDOG.357

Ford had a recall on the ignition switch several...

Ford had a recall on the ignition switch several years ago. the electrical connector would melt and cause electrical problems.
Forum: General Tech
09-19-2009, 08:05 PM
Replies: 2
Views: 780
Posted By RUDEDOG.357

If the a/c works its probably ok. the only way...

If the a/c works its probably ok. the only way it could get plugged is because the compressor is going out or the desicant bag went out. Compressor would make noise also.
08-01-2009, 12:33 AM
Replies: 15
Views: 4,651
Posted By RUDEDOG.357

run the car on the hoist and see if the...

run the car on the hoist and see if the driveshaft wobbles. ive had garter springs fall of on the pinion seal when tapping it in. causes the flange to wobble and cause a vibration. Or the pinion...
Forum: General Tech
11-17-2008, 06:55 PM
Replies: 1
Views: 241
Posted By RUDEDOG.357

ford has a new intake where the coolant crossover...

ford has a new intake where the coolant crossover is aluminum.
11-15-2008, 04:33 PM
Replies: 5
Views: 275
Posted By RUDEDOG.357

use the good felpro header gaskets. I installed...

use the good felpro header gaskets. I installed my headers and have never had to retorque the bolts.
Forum: General Tech
11-14-2008, 11:44 PM
Replies: 3
Views: 366
Posted By RUDEDOG.357

probably got air in the cooling system or the...

probably got air in the cooling system or the timing is off and engine is pinging.
11-12-2008, 09:45 PM
Replies: 7
Views: 414
Posted By RUDEDOG.357

spin the pinion to see if it feels rough. That...

spin the pinion to see if it feels rough. That may be why your pinion seal leaked.
Forum: General Tech
11-06-2008, 12:06 PM
Replies: 7
Views: 1,582
Posted By RUDEDOG.357

Ive had valve body gaskets that come apart and...

Ive had valve body gaskets that come apart and allow fluid to leak past the gaskets. sometimes you loose 2nd or third gear. The other thing I have seen is the intermediate band breaks and you loose...
10-31-2008, 08:49 PM
Replies: 13
Views: 713
Posted By RUDEDOG.357

Nice work. few questions. Did the stock...

Nice work. few questions. Did the stock throttle cable hook up to your carb? What intake and carb are you using. Im doing a 4 cyl to v8 conversion.
10-16-2008, 12:16 PM
Replies: 10
Views: 841
Posted By RUDEDOG.357

Maybe the governor is stuck. the weights might...

Maybe the governor is stuck. the weights might be hanging up. ill ck my shop manual when i get to work.
10-15-2008, 09:06 PM
Replies: 10
Views: 841
Posted By RUDEDOG.357

The bushing that holds the Throttle cable gets...

The bushing that holds the Throttle cable gets brittle and breaks. The cable comes off and trans wont upshift. the adjustment might be off. you might be able to tell where it was before by looking...
Forum: General Tech
10-14-2008, 11:54 AM
Replies: 4
Views: 457
Posted By RUDEDOG.357

We send the lock cylinders out to get coded at a...

We send the lock cylinders out to get coded at a locksmith.
10-13-2008, 10:19 PM
Replies: 11
Views: 1,239
Posted By RUDEDOG.357

probably low on charge or the low pressure switch...

probably low on charge or the low pressure switch is bad.
10-13-2008, 07:33 AM
Replies: 9
Views: 1,087
Posted By RUDEDOG.357

ck the vent on the trans. may be building...

ck the vent on the trans. may be building pressure inside the trans ans pushing it into the cable. I had a taurus that did the same thing.
10-12-2008, 03:16 PM
Replies: 11
Views: 1,239
Posted By RUDEDOG.357

If you pull the glove box down you may be able to...

If you pull the glove box down you may be able to see the line or hear if its leaking. If you dont see a broken line then I would pull the control panel.
10-12-2008, 02:33 PM
Replies: 11
Views: 1,239
Posted By RUDEDOG.357

Dont have a shop manual at home but I would ck...

Dont have a shop manual at home but I would ck for vacuum leaks under the hood. Then ck the vac hose that goes through the firewall into the dash. should be on pass side by the heater hoses. hope...
10-12-2008, 02:04 PM
Replies: 12
Views: 647
Posted By RUDEDOG.357

I have 275 on mine and I did have to remove the...

I have 275 on mine and I did have to remove the quad shocks. I have weld draglites with 5.5 spacing.
10-01-2008, 08:40 PM
Replies: 28
Views: 1,829
Posted By RUDEDOG.357

I just installed a set of gears on a 98 mustang...

I just installed a set of gears on a 98 mustang for 100.00 plus 45 for bearings. I need to raise my prices.
Forum: General Tech
10-01-2008, 08:22 PM
Replies: 3
Views: 561
Posted By RUDEDOG.357

I believe that some fords use a vacuum switch on...

I believe that some fords use a vacuum switch on the brake pedal for cruise disconnect. ck the hoses under the dash.
Showing results 1 to 25 of 36
 


 
Forum Jump

Advertising
Featured Sponsors
Vendor Directory