MustangForums.com - Search Results

Go Back  MustangForums.com > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: Mike93SVT
Showing results 1 to 25 of 155
Search took 0.30 seconds.
12-06-2007, 05:20 PM
Replies: 1
Views: 264
Posted By Mike93SVT

WTB Clean Fox Body or Trade for 2006 GSX-R 1000, silver, mint

this bike is perfect. no scratches, never been down or raced. i'm looking to get back into a mustang. i would consider taking trade on a clean fox body and cash. otherwise, i'm asking $8,300 ,...
12-04-2007, 05:25 PM
Replies: 0
Views: 287
Posted By Mike93SVT

FS/FT 2006 GSX-R 1000, Silver/Gray, Mint

this bike is perfect. no scratches, never been down or raced. i'm looking to get back into a mustang. i would consider taking trade on a clean fox body and cash. otherwise, i'm asking $8,300 ,...
Forum: 351 Mustang
08-16-2007, 09:32 PM
Replies: 10
Views: 1,932
Posted By Mike93SVT

RE: 351 turbo ??

www.turbomustangs.com (http://www.turbomustangs.com) + SEARCH Button = answer to all your questions


easily done numerous times w/ all combos and numbers
Forum: 351 Mustang
07-29-2007, 01:09 PM
Replies: 9
Views: 981
Posted By Mike93SVT

Forum: 351 Mustang
07-25-2007, 10:51 PM
Replies: 5
Views: 813
Posted By Mike93SVT

RE: just got my 418W

sounds good, but you may want to step up to a 950 carb. that 850 won't support 680 hp. good luck
Forum: 351 Mustang
07-25-2007, 10:50 PM
Replies: 2
Views: 533
Posted By Mike93SVT

RE: water?

water runs through the egr spacer to theoretically cool the air. if you block it in the beginning and end of the path you'll be fine. it's a common mod.
07-24-2007, 01:44 AM
Replies: 16
Views: 1,290
Posted By Mike93SVT

RE: The most Savage import I've seen

i've seen that car before, it's sick
07-23-2007, 03:14 AM
Replies: 26
Views: 2,398
Posted By Mike93SVT

RE: Shortblock from Fordstrokers.com any 411

excellent builders and knowledgable guy. call him first and get the right information. he'll do you right.
07-23-2007, 03:07 AM
Replies: 2
Views: 404
Posted By Mike93SVT

RE: how many would attempt this? (need help)

1- 415hp on 6lbs + bull****

2- don't even push it past 450 on a super safe tune if you can't replace the motor. they will go time and time again. so keep it safe or start buying some jy blocks...
Forum: 351 Mustang
07-20-2007, 05:20 PM
Replies: 7
Views: 818
Posted By Mike93SVT

RE: 351W

easily. that's the same motor i've got. it's a roller and used stock 92 electronics to run it. just need a different distributor to use your computer. with some high flow heads like afr 205's or...
Forum: 351 Mustang
07-20-2007, 05:18 PM
Replies: 10
Views: 1,015
Posted By Mike93SVT

RE: Blower

i'm about to do the same thing. 408 w/ either a dryers or a bds blower. mine will be in a 2900 lb 85 SSP coupe. can't wait, it's gonna scream.
07-15-2007, 11:49 PM
Replies: 13
Views: 898
Posted By Mike93SVT

RE: Mustang Flips

it's an oooolllld video. it's a turbo mustang. it had a cert. cage. the reason it looked like over correction is because it has a manual rack. so it takes more turns to move the tires. he lost...
Forum: 351 Mustang
07-04-2007, 01:45 AM
Replies: 5
Views: 1,741
Posted By Mike93SVT

RE: TKO600

i may be selling a full tko setup here shortly. it's a 1 yr old tko 600, spec stage 3 clutch, sfi bellhousing and aluminum driveshaft.
05-28-2007, 03:35 PM
Replies: 18
Views: 588
Posted By Mike93SVT

RE: removing trans from motor?

it's just stuck a bit. the dowel pins are just holding on. get a pry bar and a big hammer. it'll come off.
Forum: 351 Mustang
05-28-2007, 03:19 PM
Replies: 2
Views: 455
Posted By Mike93SVT

Block strength of a late 90's roller block?

so i've done some searching and haven't really found the answer i was looking for. my 351 is out of a 97 econoline van, so it's a roller. my questions are....what years were these series of motors in...
Forum: 351 Mustang
05-28-2007, 02:25 PM
Replies: 76
Views: 19,347
Posted By Mike93SVT

RE: Twin Turbo a 351 windsor?

here you guys go. these are 2 of the best places you can get a turbo setup from. either buy the kit, or get the hotside (what i'm doing and have done in the past) and do the cold side yourself. it...
Forum: 351 Mustang
05-28-2007, 02:16 PM
Replies: 13
Views: 1,852
Posted By Mike93SVT

RE: Build or Buy a 408 Short-Block?

hell no, i've got one. when i ran it behind a turbo 302 i couldn't even run up to my peak hp when racing. really ticked me off. it just won't go in gear in higer rpm's. now it'sbehind my stock short...
05-26-2007, 01:49 PM
Forum: 351 Mustang
05-26-2007, 05:00 AM
Replies: 19
Views: 1,094
Posted By Mike93SVT

RE: who is in here? post engine pics!

here's mine. still gotta put the wiring harness in the fenderwell and repaint the inner fenders......

http://img2.putfile.com/thumb/5/14501581153.jpg (http://www.putfile.com/pic.php?img=5534697)...
05-25-2007, 08:10 PM
Replies: 0
Views: 165
Posted By Mike93SVT

WTB Anderson PMS

i'm looking for an anderson pms series 4 for a fox body. let me know if you have one.

thanks,
mike
05-25-2007, 08:09 PM
Replies: 3
Views: 263
Posted By Mike93SVT

WTB Anderson PMS 88-93

i'm looking for an anderson pms series 4 for a fox body. let me know if you have one.

thanks,
mike
05-21-2007, 11:59 AM
Replies: 5
Views: 266
Posted By Mike93SVT

RE: 50lb Inj w/ Maf, Lakewood Bell, Centerforce clutch, Headers

it's the previous model of the dual friction. was purchased a year and a half ago, installed, and car wasn't finished. now have a tko to replace it. just want it gone, that's why it's cheap.
Showing results 1 to 25 of 155
 


 
Forum Jump

Advertising
Featured Sponsors
Vendor Directory

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.