MustangForums.com - Search Results

Go Back  MustangForums.com > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: GT Nate
Showing results 1 to 25 of 402
Search took 0.03 seconds.
03-09-2019, 08:28 AM
Replies: 5
Views: 505
Posted By GT Nate

I'd use the rear axle as 2 points and 2 points...

I'd use the rear axle as 2 points and 2 points under the front (the circles closest to the front). And for safety's sake, keep the jack positioned there just in case a jack stand fails. No use...
02-25-2019, 09:56 AM
Replies: 5
Views: 286
Posted By GT Nate

loose shock bolt, rattling in the trunk? panhard...

loose shock bolt, rattling in the trunk? panhard bar not fully tightened down to 190 ft/lb?
Forum: Detailing
02-25-2019, 09:55 AM
Replies: 11
Views: 840
Posted By GT Nate

don't use magic eraser, that's micro fine sand...

don't use magic eraser, that's micro fine sand paper...will take the sheen right off for good.
02-23-2019, 02:29 PM
Replies: 16
Views: 3,240
Posted By GT Nate

You can buy struts which already have the spring...

You can buy struts which already have the spring installed on them and it's just a matter of installing. SUPER easy, no spring compressor needed. Just the bolts at the top strut towers, undo the sway...
Forum: Detailing
02-23-2019, 02:26 PM
Replies: 11
Views: 840
Posted By GT Nate

I find that maybe windex and a few clean paper...

I find that maybe windex and a few clean paper towels pulls it up. You're cleaning looks much better. I think you nailed it.
02-02-2019, 05:21 PM
Replies: 5
Views: 350
Posted By GT Nate

EXACT same thing happened to me not more than a...

EXACT same thing happened to me not more than a month ago. One day I hear a squeal from the driver's speaker...sound came through, but always that squeal. I'd take the key out, open the door squeal...
01-16-2019, 06:55 AM
Replies: 24
Views: 1,296
Posted By GT Nate

https://www.vehiclehistory.com/ use this...

https://www.vehiclehistory.com/

use this site, will give you a full history...it's totally free.
01-13-2019, 07:51 AM
Replies: 6
Views: 318
Posted By GT Nate

looks like the other end of the line in the 2nd...

looks like the other end of the line in the 2nd picture is just hooked to the fender...
01-11-2019, 09:29 AM
Replies: 7
Views: 184
Posted By GT Nate

it's probably the trans cooler line going to the...

it's probably the trans cooler line going to the radiator. On the side of the radiator is a reservoir for trans fluid to get cooled by the air.
Red is tranny.
AC coolant is clear
01-11-2019, 09:25 AM
Replies: 6
Views: 1,085
Posted By GT Nate

mine were crap when I bought my 2010. I found out...

mine were crap when I bought my 2010. I found out later the rear brake calipers has a frozen slider pin on each side, so...no rear brakes only fronts.
Put new calipers on the rear and the braking...
Forum: Off Topic
01-10-2019, 07:54 AM
Replies: 32
Views: 813
Posted By GT Nate

we bought a brother laser printer (no ink, just...

we bought a brother laser printer (no ink, just toner which never dries) on Digg.com for $100 and it rocks.
01-09-2019, 08:28 AM
Replies: 1
Views: 1,039
Posted By GT Nate

well, that's not an S197 body... but calipers are...

well, that's not an S197 body... but calipers are calipers.
Mine are more rusty on the back too.. I had to replace both calipers as one slider pin on both was rusted solid..so no rear brakes for...
01-07-2019, 06:01 PM
Replies: 8
Views: 412
Posted By GT Nate

you can't it's the material inside the cat, the...

you can't it's the material inside the cat, the honeycomb structure has cracked and is in pieces. As the cat gets hot the rattle will cease as the parts expand.
But yes, time for a new cat.
How old...
01-07-2019, 03:24 PM
Replies: 1
Views: 387
Posted By GT Nate

could have been a stuck lifter...or a roller...

could have been a stuck lifter...or a roller rocker who knows...
they make them so complex nowadays!
Forum: Off Topic
01-07-2019, 06:48 AM
Replies: 106
Views: 2,713
Posted By GT Nate

I take one of those little acid reducing pills,...

I take one of those little acid reducing pills, takes about 20 minutes and it's gone.
01-07-2019, 06:47 AM
Replies: 2
Views: 263
Posted By GT Nate

If you can capture it dead on your phone video...

If you can capture it dead on your phone video might help the dealer see you're not BS'ing them.
Sounds like a bad ground or a wire not fully seated in the harness...
It's a bumper to bumper...
01-07-2019, 06:43 AM
Replies: 16
Views: 728
Posted By GT Nate

sure the plug wires are on the correct spark...

sure the plug wires are on the correct spark plugs for that cylinder?
01-03-2019, 10:42 AM
Replies: 9
Views: 2,171
Posted By GT Nate

there's a rust warranty which is pretty...

there's a rust warranty which is pretty extensive. They can sand and repaint the hood and you'd never see that issue again. Maybe one of the painter robots was having a bad day.
01-02-2019, 09:42 AM
Replies: 2
Views: 236
Posted By GT Nate

I had to do that too, wasn't getting a leak but...

I had to do that too, wasn't getting a leak but one day under the hood I noticed that drain and felt down into it, full of dirt, hosed it right out, never an issue since. Previous owner must have...
12-24-2018, 12:19 PM
Replies: 3
Views: 1,244
Posted By GT Nate

Dumb me! It was right there on the side, I just...

Dumb me! It was right there on the side, I just forgot about it.

Oh well, all fixed.
12-23-2018, 07:55 PM
Replies: 3
Views: 1,244
Posted By GT Nate

Looked at a diagram, it appear to go in the side...

Looked at a diagram, it appear to go in the side of the vapor cannister, but the one I bought had no hole in the side...odd
I'll have to recheck it tomorrow.

Thanks for the reply!
12-23-2018, 12:41 PM
Replies: 3
Views: 1,244
Posted By GT Nate

WHERE IS THE VAPOR CANNISTER VENT VALVE SOLENOID ON MY 2010 GT??

https://cimg6.ibsrv.net/gimg/mustangforums.com-vbulletin/600x466/cvs20photo_20primary_ra_p_228c864b1ae39ab7af073f5e5665014d60e94064.jpg
Where is this part located, I didn't see it in the engine bay?...
12-21-2018, 09:38 AM
Replies: 2
Views: 395
Posted By GT Nate

heaters are laid on top of the foam. Coolers...

heaters are laid on top of the foam. Coolers would require piping to get air into the seats. 2014 will have side airbags, but most aftermarket makers put stitching on the side which will break if an...
12-19-2018, 09:14 AM
Replies: 5
Views: 432
Posted By GT Nate

one option, is to go to a hardware store with a...

one option, is to go to a hardware store with a rear bolt and check the thread pattern and size and buy one, might need to cut it down some.
or go to a junkyard and get one off a rear Stang...if...
12-19-2018, 09:11 AM
Replies: 6
Views: 556
Posted By GT Nate

It's all throttle by wire, the throttle pedal is...

It's all throttle by wire, the throttle pedal is bolted to the firewall and has one connection. and 3 bolts. You can remove it, the connector and take it out. Then there's about 5 hex screws holding...
Showing results 1 to 25 of 402
 


 
Forum Jump

Advertising
Featured Sponsors
Vendor Directory

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.