MustangForums.com - Search Results

Notices
 
Search: Posts Made By: imp
Showing results 1 to 25 of 500
Search took 0.02 seconds.
06-11-2019, 10:33 PM
Replies: 3
Views: 214
Posted By imp

Look at the front crankshaft pulley/vibration...

Look at the front crankshaft pulley/vibration damper. HiPos had a wider damper, approximately 1-1/4-inch wide, maybe more.
06-10-2019, 10:52 PM
Replies: 5
Views: 809
Posted By imp

If you want it to run really better, start...

If you want it to run really better, start looking for vacuum leaks. Easy enough to figure out where vacuum is present: hoses, hose ends especially, bad PCV valve, harder to spot intake manifold...
06-10-2019, 10:49 PM
Replies: 3
Views: 214
Posted By imp

I ordered my K car in August, 1964, with High...

I ordered my K car in August, 1964, with High Performance Package. It took 5 weeks to get it, Color Vintage Burgundy, 2 door coupe. The engine featured screwed-in rocker studs instead of pressed-in,...
06-06-2019, 10:44 PM
Replies: 5
Views: 809
Posted By imp

I believe if the IAC is "bad", that is, not...

I believe if the IAC is "bad", that is, not opening at all, AND there are absolutely no vacuum leaks anywhere, the engine will try to fire, but not run, with the IAC unplugged. Thus, I'm guessing IAC...
06-06-2019, 10:40 PM
Replies: 16
Views: 1,156
Posted By imp

wbrockstar Good show! The only thing...

wbrockstar

Good show!
The only thing which might mislead him is your CLIP is of an engine of pre-94 vintage, having the distributor-mounted TFI module. In '94 it was moved to a cooler, remote...
06-06-2019, 11:58 AM
Replies: 5
Views: 809
Posted By imp

If it runs better with the IAC unplugged, there...

If it runs better with the IAC unplugged, there likely is a vacuum leak somewhere allowing air to enter unmeasured, confusing the computer. Check all places, hoses for cracks, where air could be...
05-28-2019, 10:12 PM
Replies: 10
Views: 886
Posted By imp

I have a much earlier car, 1994, but found the...

I have a much earlier car, 1994, but found the driver's side front O2 was easily accessed via under the wheel-well. If necessary, use a crow's foot wrench.
Forum: General Tech
05-23-2019, 10:55 PM
Replies: 2
Views: 1,553
Posted By imp

I would put an AOD in it. Likely a bolt-in,...

I would put an AOD in it. Likely a bolt-in, minimal rework if not, possible even the overall length would require no driveshaft alteration. imp
05-19-2019, 10:44 PM
Replies: 9
Views: 1,190
Posted By imp

I can tell you about my '93 Cobra, but do nor...

I can tell you about my '93 Cobra, but do nor know year of your own vehicle. I bought the Cobra with crunched RF fender, deployed bag hanging out. Cut bag off, glued the swing out flap back in place....
05-12-2019, 09:24 PM
Replies: 3
Views: 296
Posted By imp

A lot of blue paint was wasted on the...

A lot of blue paint was wasted on the newspaper.......Do you get intake, carb, exh. manifolds, valve covers, timing cover, oil pan? Ask why these parts were removed, was trouble being experienced...
05-06-2019, 11:18 PM
Replies: 3
Views: 343
Posted By imp

OK, before you get her running and push it like a...

OK, before you get her running and push it like a K engine, I'd figger out whether it really is a K. Otherwise, you might get some nasty surprises.

Yank off a valve cover, look at the rocker...
05-06-2019, 11:14 PM
Replies: 1
Views: 280
Posted By imp

I'll go out to my shop tomorrow AM, and look at...

I'll go out to my shop tomorrow AM, and look at the fan I removed from my '94. It's junk, and I now have a clutch fan. imp
05-06-2019, 11:08 PM
Replies: 10
Views: 503
Posted By imp

You can get a rebuilt computer here: ...

You can get a rebuilt computer here:

https://www.fs1inc.com/

Mine cost $150. imp
05-04-2019, 10:55 PM
Replies: 3
Views: 343
Posted By imp

If it's a "K" car, it will have a dual-point...

If it's a "K" car, it will have a dual-point distributor with no vacuum advance provision, unless the distributor has been replaced. Electronic ignition is nice, especially if it uses a Hall-effect...
05-04-2019, 10:52 PM
Replies: 5
Views: 485
Posted By imp

Determine which fuse is feeding power to the...

Determine which fuse is feeding power to the stereo and remove it. If the battery then remains charged, there is something haywire with the stereo wiring; maybe it's internals are not shutting off.
...
05-03-2019, 10:49 PM
Replies: 3
Views: 2,112
Posted By imp

Glad I could help!

Glad I could help!
04-30-2019, 10:52 PM
Replies: 2
Views: 449
Posted By imp

Interesting that you have a '95 with a 4.6. To my...

Interesting that you have a '95 with a 4.6. To my knowledge, the 4.6 was not introduced in Mustang until model year 1996; Ford had a TON of 5.0HOs already inventoried when '95 production stopped, and...
04-29-2019, 11:04 PM
Replies: 3
Views: 2,112
Posted By imp

Can you get someone who has a dial caliper or...

Can you get someone who has a dial caliper or micrometer and measure the diameter over the threads? I've had them apart many times, but very long ago. I'll guess it's about 5/8" diameter, but maybe...
04-27-2019, 07:24 PM
Replies: 12
Views: 2,351
Posted By imp

No one has mentioned the galley plugs in the rear...

No one has mentioned the galley plugs in the rear of the block. Course, in front the oil leak would be contained, but in the rear, it would leak out under the clutch/converter housing. Have you...
04-22-2019, 11:03 PM
Replies: 4
Views: 162
Posted By imp

Newer modules sold by Ford Parts were said to be...

Newer modules sold by Ford Parts were said to be re-designed to handle higher temps. for long periods. As long as yours lasted (if original), it seems a moot point. Aftermarket parts maybe another...
04-21-2019, 11:06 PM
Replies: 4
Views: 162
Posted By imp

This would be the TFI Module, mounted on the...

This would be the TFI Module, mounted on the distributor? 5.0 HO engine?

It was removed from the distributor in 1994, located mounted on a heat sink, 1995 was the last time, 5.0 was discontinued...
04-21-2019, 11:02 PM
Replies: 1
Views: 238
Posted By imp

Good example showing the need to view and...

Good example showing the need to view and interpret codes! Wish mine was that easy, it's been unsolved for over a year.......
04-18-2019, 10:57 PM
Replies: 2
Views: 107
Posted By imp

Check the return spring which closes the throttle...

Check the return spring which closes the throttle plate. Also, remove the spring and move the throttle plate by hand with your fingers, feeling if the plate closes smoothly and easily down to the...
Forum: General Tech
04-17-2019, 10:45 PM
Replies: 10
Views: 1,741
Posted By imp

If they are rounded off, like these, sometimes...

If they are rounded off, like these, sometimes even cone-shaped, ya can't drive a socket onto them very well. Can a socket grip them tightly enough? Your idea is, a good one, I admit, and if I ever...
Forum: General Tech
04-16-2019, 09:59 PM
Replies: 10
Views: 1,741
Posted By imp

The "trick" lug nuts may often be loosened using...

The "trick" lug nuts may often be loosened using a very sharp cold chisel and hammer, angling and driving in the direction of loosening.
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.