Install Clear corners - MustangForums.com



V6 S197 General Discussion This section is for technical discussions pertaining specifically to the V6 variation of the 2005 and newer Ford Mustang.

Reply
 
 
 
Thread Tools Search this Thread
Old 03-02-2006, 08:22 PM   #1  
scheetz83
2nd Gear Member
Thread Starter
 
scheetz83's Avatar
 
Join Date: Apr 2005
Location: Washington
Posts: 451
Default Install Clear corners

so i was under my car and i was all geared up to install the clr front markers but it is starting to rain so i was in a hurry to get them out but i did not have any luck... started to rain pretty good and i did not want to rush "Thats when accidents happen"

Here is my (?) did any one who installed these. did you have to take lose the inner wheel well to get the lights out

thanks
scheetz83 is offline   Reply With Quote
Old 03-02-2006, 08:55 PM   #2  
vistapony
2nd Gear Member
 
Join Date: Jan 2006
Location:
Posts: 167
Default RE: Install Clear corners

Better to take your time! They'll look great though!
vistapony is offline   Reply With Quote
Old 03-03-2006, 01:05 AM   #3  
danalor
1st Gear Member
 
Join Date: May 2005
Posts: 112
Default RE: Install Clear corners

Just did mine the other night, I took the wheels off and the three lower screws on the wheel well. With the three screws removed I was able to pull the well aside to remove the lights. You may be able to be do it without moving the well but it will be very very tight and I didn't want to risk breaking the lense by forcing it. When you remove the lights they have two clips holding the end on just squeeze the clip and push the lense in from outside the bumper, it's alot easier than trying to squeeze the clip and pull the light out especially if you have big hands.
danalor is offline   Reply With Quote
Old 03-03-2006, 03:12 AM   #4  
scheetz83
2nd Gear Member
Thread Starter
 
scheetz83's Avatar
 
Join Date: Apr 2005
Location: Washington
Posts: 451
Default RE: Install Clear corners

Quote:
ORIGINAL: danalor

Just did mine the other night, I took the wheels off and the three lower screws on the wheel well. With the three screws removed I was able to pull the well aside to remove the lights. You may be able to be do it without moving the well but it will be very very tight and I didn't want to risk breaking the lense by forcing it. When you remove the lights they have two clips holding the end on just squeeze the clip and push the lense in from outside the bumper, it's alot easier than trying to squeeze the clip and pull the light out especially if you have big hands.

thanks maby tomara i might run my car in the shop while i am working and get them in
scheetz83 is offline   Reply With Quote
Old 03-03-2006, 02:44 PM   #5  
cstigger04
2nd Gear Member
 
Join Date: Jan 2006
Location:
Posts: 309
Default RE: Install Clear corners

take the 3 screws out and the middle push pin from the inner fender panel it will make it so much easier.....trust me it will be a 10 min job if you do and you won't break anything.
cstigger04 is offline   Reply With Quote
Old 03-08-2006, 02:59 PM   #6  
Sevalley
1st Gear Member
 
Join Date: Jan 2006
Location:
Posts: 130
Default RE: Install Clear corners

where did you purchase clear corners for the 2005 mustang? I cant seem to find them anywhere.
Sevalley is offline   Reply With Quote
Old 03-08-2006, 07:36 PM   #7  
KiLLeR_WoMBaT
1st Gear Member
 
Join Date: Dec 2005
Location:
Posts: 140
Default RE: Install Clear corners

They are ALL over eBay.



Quote:
ORIGINAL: Sevalley

where did you purchase clear corners for the 2005 mustang? I cant seem to find them anywhere.
KiLLeR_WoMBaT is offline   Reply With Quote
Old 03-08-2006, 10:04 PM   #8  
onefastv6
3rd Gear Member
 
Join Date: Jul 2005
Location: san diego
Posts: 801
Default RE: Install Clear corners

ill be looking for them
onefastv6 is offline   Reply With Quote
Old 03-08-2006, 11:19 PM   #9  
cstigger04
2nd Gear Member
 
Join Date: Jan 2006
Location:
Posts: 309
Default RE: Install Clear corners

Ebay ....look up Revotec $62.50 shipped to you in 3 days....wonderful product and the pattern inside matches the headlights Comes with blubs too but I just used the factory clear ones.
cstigger04 is offline   Reply With Quote
Old 03-09-2006, 12:16 AM   #10  
Puleo76
3rd Gear Member
 
Join Date: Dec 2005
Location:
Posts: 772
Default RE: Install Clear corners

how do u guys think these would look in a screaming yellow??
Puleo76 is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
Rear Suspension 2001 GT GimpyHSHS 4.6L (1996-2004 Modular) Mustang 3 09-18-2015 12:27 PM
Happy with new Steeda suspension on my 2010 GT robjh22 Suspension 0 09-08-2015 12:47 PM
Steeda & Nitto Tire Testing NT555 G2 - Great Photos Inside!! [email protected] Steeda Autosports 0 09-08-2015 11:50 AM
Help! Metra 70-5521 AMP Harness Install cbird1177711 2005-2014 Mustangs 2 09-03-2015 08:43 PM
Hydro dipped carbon fiber Fuel Door SYNY5TER Parts For Sale 0 09-02-2015 01:35 AM


Tags
2006, clear, corner, corners, install, mustang

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Forum Jump

Advertising
Featured Sponsors
Vendor Directory

All times are GMT -5. The time now is 09:47 AM.


© 2018 MH Sub I, LLC dba Internet Brands
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.