6 point roll cage
02-09-2014, 09:23 AM
#1
2nd Gear Member
Thread Starter
Join Date: Oct 2012
Location: New Jersey
Posts: 164
6 point roll cage
I have a 2012 and Was looking for some pics and maybe a little advice on installation tips on
A roll cage. I just ordered RPM's 6 pointer. Any help would be greatly appreciated. I will post some pics when finished. I was planing on recording the install as well.
I recently helped my brother with his camaro convertible install and it sucked!
A roll cage. I just ordered RPM's 6 pointer. Any help would be greatly appreciated. I will post some pics when finished. I was planing on recording the install as well.
I recently helped my brother with his camaro convertible install and it sucked!
02-09-2014, 11:01 AM
#2
Moderator
Join Date: May 2006
Location: Michigan again!
Posts: 8,579
Do you have a link to the RPM bar? I had one custom fabricated for my 2006, install wasn't bad. I took it out when I sold the car to use with the 2013 and my fabricator is going to do some work on it to fit around the CDC light bar. Mine didn't go through the panels. I had swing out/removable door bars.
He did this one for a friend
He did this one for a friend
02-09-2014, 05:56 PM
#3
2nd Gear Member
Thread Starter
Join Date: Oct 2012
Location: New Jersey
Posts: 164
www.trackspecmotorsports.com is where I ordered the bar. They work very closely with RPM, Who also has a website,with these bars. They are a bit $$$ but they do come complete.there price is with paint,hardware and IS welded. You just have to bolt it in. And they ar NHRA CERTIFIED.
I haven't found another 6 pointer that included all this with a bolt in.
I like the stripe continuing on your bar, nice touch. Thanks for the pics. The RPM bar does require you to cut the rear panel.
Keep us updated on your bar. I would like to see finished product
I haven't found another 6 pointer that included all this with a bolt in.
I like the stripe continuing on your bar, nice touch. Thanks for the pics. The RPM bar does require you to cut the rear panel.
Keep us updated on your bar. I would like to see finished product
02-09-2014, 06:11 PM
#4
2nd Gear Member
Thread Starter
Join Date: Oct 2012
Location: New Jersey
Posts: 164
[QUOTE=runninpony6;8347065]www.trackspecmotorsports.com is where I ordered the bar. They work very closely with RPM, Who also has a website,with these bars. They are a bit $$$ but they do come complete.there price is with paint,hardware and IS welded. You just have to bolt it in. And they ar NHRA CERTIFIED.
I haven't found another 6 pointer that included all this with a bolt in.
I like the stripe continuing on your bar, nice touch. Thanks for the pics. The RPM bar does require you to cut the rear panel.
Keep us updated on your bar. I would like to see finished product
I haven't found another 6 pointer that included all this with a bolt in.
I like the stripe continuing on your bar, nice touch. Thanks for the pics. The RPM bar does require you to cut the rear panel.
Keep us updated on your bar. I would like to see finished product
Last edited by runninpony6; 02-09-2014 at 06:12 PM. Reason: Picture wouldn't load
02-09-2014, 06:24 PM
#5
2nd Gear Member
Thread Starter
Join Date: Oct 2012
Location: New Jersey
Posts: 164
www.trackspecmotorsports.com is where I ordered the bar. They work very closely with RPM, Who also has a website,with these bars. They are a bit $$$ but they do come complete.there price is with paint,hardware and IS welded. You just have to bolt it in. And they ar NHRA CERTIFIED.
I haven't found another 6 pointer that included all this with a bolt in.
I like the stripe continuing on your bar, nice touch. Thanks for the pics. The RPM bar does require you to cut the rear panel.
Keep us updated on your bar. I would like to see finished product
I haven't found another 6 pointer that included all this with a bolt in.
I like the stripe continuing on your bar, nice touch. Thanks for the pics. The RPM bar does require you to cut the rear panel.
Keep us updated on your bar. I would like to see finished product
https://mustangforums.com/forum/memb...8204-image.jpg
02-10-2014, 05:43 PM
#7
2nd Gear Member
Thread Starter
Join Date: Oct 2012
Location: New Jersey
Posts: 164
Thanks, I did go with the Swing out door bars. Did you have to modifiy the rear panels much?
03-27-2014, 05:46 PM
#9
2nd Gear Member
Thread Starter
Join Date: Oct 2012
Location: New Jersey
Posts: 164
03-27-2014, 06:45 PM
#10
3rd Gear Member
Join Date: Jun 2010
Location: RI
Posts: 690
Awesome, congrats. I want one (and according to the track I run at, need one) I have been looking at the RPM's as well. Would love to get a chrome moly with the blue carbon fiber finish. Anyway, from the research I have done, probably the biggest install pain will be the foot posts for the door bars.