Last edit by: IB Advertising
See related guides and technical advice from our community experts:
Browse all: Powertrain Guides
- Ford Mustang Gt 1996 to 2004: How to Replace Spark Plugs and Ignition Coils
Step by step instructions for do-it-yourself repairs
Browse all: Powertrain Guides
COP Information
#22
only codes is for the o2 and thats because i don't have the MIL for the o/r x pipe or a hand tuner to disable it. The car misfires during cold start at idle, but very little misfire nothing crazy. I tried to use the IAC mod to drop the revs quicker and it started to misfire even more during idle and it caused the car to smoke out the tail pipes when I was coming to a dead stop. But without the IAC mod the idle is normal and it doesn't smoke out the tail pipe.
#23
I know this is old but extremely helpful! So I am suspecting I have a bad coil(s) on my 02 GT. So basically what you guys are saying is while my engine is running, unplug ONE COP and then if I hear a difference in engine sound take note then plug it back in. Then check the next and see if there is a difference and take note. Whichever one(s) DONT make the engine sound different are the possible bad ones that I should probably think about changing?
Thanks so much!
Thanks so much!
#24
Well after working with Mark at Weapon X for over a year, doing a number of field tests and beta testing on new designs Back in January of this year i received a set of the current production EFX COPs for extended testing.
Having run them since that time, most recently on a 440 mile round trip in 95°F to 100°F+ heat, I am pleased to say that the heat problems I experienced with the earlier designs have been overcome. The new design performs flawlessly in the high temperatures and delivers the tweaked performance I described in my initial impressions described earlier in this thread--and has been doing so for 8 months and 20k miles.
I also have to say that I have never dealt with a manufacturer/vendor that was any more dedicated to working with me to get things right. Kudo's to Mark and WeaponX for their commitment to their products and customers!!!
Having run them since that time, most recently on a 440 mile round trip in 95°F to 100°F+ heat, I am pleased to say that the heat problems I experienced with the earlier designs have been overcome. The new design performs flawlessly in the high temperatures and delivers the tweaked performance I described in my initial impressions described earlier in this thread--and has been doing so for 8 months and 20k miles.
I also have to say that I have never dealt with a manufacturer/vendor that was any more dedicated to working with me to get things right. Kudo's to Mark and WeaponX for their commitment to their products and customers!!!
Last edited by cliffyk; 08-01-2012 at 06:19 PM.
#26
I went to a local sign shop almost a couple years ago now, explained to the owner what I was doing, and that I just needed three pieces a couple inches wide by 24 inches. He rummaged through his scrap bin and came up with enough to stripe five cars.
I asked him what I owed and he said "You're making a flag aren't you? Get the Hèll outa' here..."
I asked him what I owed and he said "You're making a flag aren't you? Get the Hèll outa' here..."
#28
However I have to ask: Can you return them for a refund?
They do not have a good reputation for long term reliability, often failing in just 15k to 20k miles, and are no better--they actually they have a bit less maximum potential output in my testing (50 kV vs. 55 kV)--than the stock COPS.
Testing an Accel COP (here is a video of an Accel COP firing across a 15 mm air gap):
Results Accel vs. OEM:
The lower output is not enough to be relevant, as it only takes 15kV to 16kV to ionise the gap and just 5kV to 6kV to maintain the spark.
The EECV system fires each plug 3 times in rapid succession at idle and up to 1200 rpm or so:
However their poor reliability history is...