Notices
4.6L V8 Technical Discussions Any questions about engine, transmission, or gearing can be asked here!

kenne bell issues

Thread Tools
 
Search this Thread
 
Old 06-27-2010, 01:17 PM
  #1  
tweeked
Thread Starter
 
tweeked's Avatar
 
Join Date: Jun 2010
Location: texas
Posts: 5
Default kenne bell issues

i got a 05 gt ,thumper cams(stage 1 with timing deletes)just had supercharger(kennebell) installed.runs well till you hit the throttle as soon as you let off it codes up 2106 ,its been at a speed shop going on 2 months they are blaming the cams ? car ran great on cams before .
tweeked is offline  
Old 06-28-2010, 09:37 AM
  #2  
tx_zstang
5th Gear Member
 
tx_zstang's Avatar
 
Join Date: May 2007
Location: Central Texas
Posts: 2,388
Default

P2106
Throttle Actuator Control System - Forced Limited Power

Tune issue? Or maybe a damaged wire to the throttle body when pulling it out of the loom and/or re-routing it?
tx_zstang is offline  
Old 06-29-2010, 12:19 AM
  #3  
Simon1
5th Gear Member
 
Simon1's Avatar
 
Join Date: Dec 2006
Location: Redding, CA
Posts: 4,552
Default

Who is tuning the car?

What is stage 1 with timing deletes.
Simon1 is offline  
Old 06-29-2010, 06:04 PM
  #4  
tweeked
Thread Starter
 
tweeked's Avatar
 
Join Date: Jun 2010
Location: texas
Posts: 5
Default

basic thumper comp cams with recomended timijng deletes
tweeked is offline  
Old 06-29-2010, 06:18 PM
  #5  
tweeked
Thread Starter
 
tweeked's Avatar
 
Join Date: Jun 2010
Location: texas
Posts: 5
Default

screamin yellow erbach lowered concept hood msd coil packs bbk throttle body bbk long tube,high flow cats,flow master mufflers. 3500 stall converter 4/10 rear end.shifter and new kenne belle supercharger that hasnt made a good run anywhere to include the local streets....
tweeked is offline  
Old 06-30-2010, 10:06 AM
  #6  
hammeron
6th Gear Member
 
hammeron's Avatar
 
Join Date: May 2006
Location: Nicely done
Posts: 11,881
Default

sorry for your troubles tweeked. i would be tempted to reinstall the stock cams and remove the bbk throttle body, until the car is up and running normally.
hammeron is offline  
Old 06-30-2010, 04:49 PM
  #7  
Simon1
5th Gear Member
 
Simon1's Avatar
 
Join Date: Dec 2006
Location: Redding, CA
Posts: 4,552
Default

Originally Posted by tweeked
basic thumper comp cams with recomended timijng deletes
Are you talking about the limiters for the VCT system?

IS it a limiter or locked out? There is a huge difference.


I suspect the people who are tryng to tune it are clueless with the S197.
Simon1 is offline  
Old 01-15-2012, 08:31 AM
  #8  
tweeked
Thread Starter
 
tweeked's Avatar
 
Join Date: Jun 2010
Location: texas
Posts: 5
Default kenne bell issues

well been a while,finally found a mustang tuner that fixed the car finally, we ran the car thru the 1/8 and were happy with 7.52 just at a 100 mph with out beating it up drove it to the strip and back !!
tweeked is offline  
Old 01-16-2012, 11:43 AM
  #9  
Simon1
5th Gear Member
 
Simon1's Avatar
 
Join Date: Dec 2006
Location: Redding, CA
Posts: 4,552
Default

Good. At 100 mph in the 1/8 you should be at 7.0-7.1. What are your 60' times? Tires? Dynograph?
Simon1 is offline  
Old 01-16-2012, 11:44 AM
  #10  
Simon1
5th Gear Member
 
Simon1's Avatar
 
Join Date: Dec 2006
Location: Redding, CA
Posts: 4,552
Default

Originally Posted by tweeked
well been a while,finally found a mustang tuner that fixed the car finally, we ran the car thru the 1/8 and were happy with 7.52 just at a 100 mph with out beating it up drove it to the strip and back !!
So it was tuning?
Simon1 is offline  


Quick Reply: kenne bell issues



All times are GMT -5. The time now is 11:15 PM.