1967 coupe / possible sale or trade
#1
1967 coupe / possible sale or trade
well, things come and go and this one has to go. i'm re-enlisting in the army - here's what i have
1967 Mustang Coupe w/ 83,xxx original miles
400 or so miles since rebuild
rebuilt and bored .30 over 289, new main bearings, new cam bearings, freeze plugs etc.
GT40P Heads w/ fresh valve job
Comp Cams valve springs
Comp Cams magnum pushrods
Comp Cams roller tip rockers
Comp Cams 10 degree valve locks
Comp Cams retainers
Comp Cams XE268H Cam
ADS Gilmer Belt setup
Performer RPM Intake manifold (port matched)
Milodon high output water pump
Summit 110GPH mechanical fuel pump
Holley 4160c 600cfm carburetor
Tri Y headers (custom fit for the P heads)
brand new Autolite distributor with Pertronix Ignitor ignition
New coil
Moroso wires
K&N 4" air filter w/ 2 1/4" drop base
Ford 8.8 Rear Axle w/ 3.08 rear and new brakes
2600-2800 Stall
C4 w/ new valve body new seals etc.
dual flowmaster 40 exhaust with dumps
1" phenolic spacer
front granada disc brake conversion with all new parts from discbrakeswap.com with new master cylinder etc.
all new aluminum fuel lines, new stainless brake lines, new fuel sending unit, new gas tank
bullitt style 17" rims 245/45/17 front 255/45/17 rear
brand new interior (hand did all seats) new a pillars, new door skins, have steel divider for back seat, and steel package tray with speaker holes. new dome light (lol) new gauge overlays new dash pad, triple gauges, and new fuel pressure / vac gauge. all new inner door handles. grant wood steering wheel with mustang cap. new seat belts etc.
new mirrors, new door handles (not installed)
car has new front frame rails, front cross member, fender aprons, all floor pans, rear frame rails and inner trunk (over $2800.00 at npd) all done on a jig.
brand new suspension, completely. all new Grab A Trak front and rear suspension from MustangsPlus.com all new upper and lower arms, front and rear swaybar (rear not installed)
the bads )
speedometer doesn't work (probably misaligned or non lubed cable (will fix)
some dings, paint job isn't the best, trunk had a stupid mach 1 wing on it, so it has holes on it but i have them covered. transmission kickdown not hooked up (brand new) but transmission works just fine and downshifts just fine. has no hood anymore but i have the stock one. some interior pieces not installed (but have all) needs new rubber around the door windows, rear bumper has some rust on the bottom side, no headliner, no radio, no antenna.
including - 3.73 ring and pinion, original 289 heads, intake, carb, HEI Distributor (new) new R model front fascia, taurus electric fan conversion, master chassis bolt kit, and engine kit. stock hood, and also the mach 1 wing. new gaskets, gear drive kit etc.
i have almost every single receipt for parts that were purchased as well as pictures from the rebuild process.
a holley fuel pressure regulator
prothane transmission mount
prothane engine mounts
as well as including shelby fiberglass side scoops, and i have all new hood bumpers as well as hood/cowl seal. anything else i forget i'll re-add to here.
and yes i know some of the wires are everywhere, as i have not had the time to put them in wire looms and neaten everything up, but i will before car is sold.
please, no lowball or silly offers, only serious ones as i do not have time to waste with them.
the only trades considered are 79-93 5.0's / notch or hatch - NO VERTS
94-98 GT's or Cobras - also NO VERTS
i have a lot of time in this car and money and i'm sad to see it go, but please do not waste my time with games. thank you.
1967 Mustang Coupe w/ 83,xxx original miles
400 or so miles since rebuild
rebuilt and bored .30 over 289, new main bearings, new cam bearings, freeze plugs etc.
GT40P Heads w/ fresh valve job
Comp Cams valve springs
Comp Cams magnum pushrods
Comp Cams roller tip rockers
Comp Cams 10 degree valve locks
Comp Cams retainers
Comp Cams XE268H Cam
ADS Gilmer Belt setup
Performer RPM Intake manifold (port matched)
Milodon high output water pump
Summit 110GPH mechanical fuel pump
Holley 4160c 600cfm carburetor
Tri Y headers (custom fit for the P heads)
brand new Autolite distributor with Pertronix Ignitor ignition
New coil
Moroso wires
K&N 4" air filter w/ 2 1/4" drop base
Ford 8.8 Rear Axle w/ 3.08 rear and new brakes
2600-2800 Stall
C4 w/ new valve body new seals etc.
dual flowmaster 40 exhaust with dumps
1" phenolic spacer
front granada disc brake conversion with all new parts from discbrakeswap.com with new master cylinder etc.
all new aluminum fuel lines, new stainless brake lines, new fuel sending unit, new gas tank
bullitt style 17" rims 245/45/17 front 255/45/17 rear
brand new interior (hand did all seats) new a pillars, new door skins, have steel divider for back seat, and steel package tray with speaker holes. new dome light (lol) new gauge overlays new dash pad, triple gauges, and new fuel pressure / vac gauge. all new inner door handles. grant wood steering wheel with mustang cap. new seat belts etc.
new mirrors, new door handles (not installed)
car has new front frame rails, front cross member, fender aprons, all floor pans, rear frame rails and inner trunk (over $2800.00 at npd) all done on a jig.
brand new suspension, completely. all new Grab A Trak front and rear suspension from MustangsPlus.com all new upper and lower arms, front and rear swaybar (rear not installed)
the bads )
speedometer doesn't work (probably misaligned or non lubed cable (will fix)
some dings, paint job isn't the best, trunk had a stupid mach 1 wing on it, so it has holes on it but i have them covered. transmission kickdown not hooked up (brand new) but transmission works just fine and downshifts just fine. has no hood anymore but i have the stock one. some interior pieces not installed (but have all) needs new rubber around the door windows, rear bumper has some rust on the bottom side, no headliner, no radio, no antenna.
including - 3.73 ring and pinion, original 289 heads, intake, carb, HEI Distributor (new) new R model front fascia, taurus electric fan conversion, master chassis bolt kit, and engine kit. stock hood, and also the mach 1 wing. new gaskets, gear drive kit etc.
i have almost every single receipt for parts that were purchased as well as pictures from the rebuild process.
a holley fuel pressure regulator
prothane transmission mount
prothane engine mounts
as well as including shelby fiberglass side scoops, and i have all new hood bumpers as well as hood/cowl seal. anything else i forget i'll re-add to here.
and yes i know some of the wires are everywhere, as i have not had the time to put them in wire looms and neaten everything up, but i will before car is sold.
please, no lowball or silly offers, only serious ones as i do not have time to waste with them.
the only trades considered are 79-93 5.0's / notch or hatch - NO VERTS
94-98 GT's or Cobras - also NO VERTS
i have a lot of time in this car and money and i'm sad to see it go, but please do not waste my time with games. thank you.
#4
RE: 1967 coupe / possible sale or trade
any pics? jake1113@gmail.com ..... i got a 99 chevy silverado ext cab with black leather and perfect body-no dents....also rhino lining....completey decked out....wanna trade?
#5
RE: 1967 coupe / possible sale or trade
Hey, I have my 88 hatch in my sig, Dunno how great of condition you're looking for though? If your interested at all, PM me and I'll let ya know all about my car, and see if there's anything else I can throw in to make you interested.
#6
RE: 1967 coupe / possible sale or trade
damn i apologize everyone i haven't been on here much - and for some reason i couldn't get private messages but now it's all fixed. i'll try to get back to everyone by the end of the day.
#7
RE: 1967 coupe / possible sale or trade
hey man, just let me know either way if you're interested at all. I'll do whatever I can to make it work if you're interested at all.
#8
RE: 1967 coupe / possible sale or trade
forgot to add, having a new TCI SuperStreet Fighter put in this week just for kicks, never liked the original tranny anyway
Thread
Thread Starter
Forum
Replies
Last Post
Matt's 95 Stang
5.0L (1979-1995) Mustang
2
10-05-2015 07:16 AM