V6 (1994-2004) Mustangs Technical discussions on the 3.8L and 3.9L V6 torque monsters

Squealing noise from engine

Thread Tools
 
Search this Thread
 
Old Dec 5, 2011 | 09:14 PM
  #1  
joeyv12's Avatar
joeyv12
Thread Starter
 
Joined: Dec 2011
Posts: 7
From: KY
Default Squealing noise from engine

my 96 3.8 is making a squeeling noise after it warms up. it sounds like it is coming from the left side of the engine. i have changed the harmonic balancer, the alternator, the water pump,the power steering pump and the cam shaft sensor and it is still there.When i shut the engine off i hear a hissing that sounds like a big air leak.The noise almost sounds like it is in the engine itself.This enginer has 3000 on a rebuid. Any suggestions would be appreciated.
Old Dec 6, 2011 | 08:54 AM
  #2  
desertt5's Avatar
desertt5
1st Gear Member
 
Joined: Jan 2010
Posts: 96
From: NM
Default

Have you tried to use a mechanics stethescope to narrow it down? Also remove the belt on front and see if it goes away. Did you replace the entire cam shaft synchronizer or just the sensor mounted on top?
Old Dec 7, 2011 | 12:24 AM
  #3  
joeyv12's Avatar
joeyv12
Thread Starter
 
Joined: Dec 2011
Posts: 7
From: KY
Default

no i haven't done that yet but i replaced the power steering pump and lines tonight,after completing the task i took the car for a ride to get it to operating temp,when i returned to my garage that noise was back. I noticed that when placed in park the noise stopped. It started again when i put it in reverse and drive it stopped in park and neutral. The tranny was also rebuilt with the engine.
Old Dec 7, 2011 | 12:28 AM
  #4  
joeyv12's Avatar
joeyv12
Thread Starter
 
Joined: Dec 2011
Posts: 7
From: KY
Default

the noise is a cylical chirping
Old Dec 7, 2011 | 01:49 PM
  #5  
desertt5's Avatar
desertt5
1st Gear Member
 
Joined: Jan 2010
Posts: 96
From: NM
Default

That is what mine sounded like.

Did you replace the entire cam shaft synchronizer or just the sensor mounted on top?
If it was the whole synchronizer, what brand?
Old Dec 7, 2011 | 07:14 PM
  #6  
joeyv12's Avatar
joeyv12
Thread Starter
 
Joined: Dec 2011
Posts: 7
From: KY
Default

yes i changed the entire synczr,i think i got it from autozone don't remember. The noise only starts when car is placed into gear, it slowly stops if put in neutral or park, but does reappearn when you shut the engine off, you hear the squel slow down to a stop.
Old Dec 10, 2011 | 02:17 PM
  #7  
joeyv12's Avatar
joeyv12
Thread Starter
 
Joined: Dec 2011
Posts: 7
From: KY
Default

i just found out that the noise is coming from the tranny bellhousing right about where the torque converter is,this has been replaced a couple of weeks ago, any ideas would be appreciated.
Old Dec 10, 2011 | 05:59 PM
  #8  
Jethro_N's Avatar
Jethro_N
 
Joined: Nov 2011
Posts: 16
From: Mississippi
Default

Originally Posted by joeyv12
i just found out that the noise is coming from the tranny bellhousing right about where the torque converter is,this has been replaced a couple of weeks ago, any ideas would be appreciated.
Did the torque converter get bolted back to the flywheel? Also, if the TC was replaced, did you make sure the converter was seated all the way onto the trans?
Old Dec 10, 2011 | 06:01 PM
  #9  
gyea's Avatar
gyea
3rd Gear Member
 
Joined: Dec 2006
Posts: 617
From: Canada EH
Default

Take it back to whoever replaced it to start....
Old Dec 11, 2011 | 12:58 PM
  #10  
joeyv12's Avatar
joeyv12
Thread Starter
 
Joined: Dec 2011
Posts: 7
From: KY
Default

I replaced the TQ myself and yes it was installed properly. I changes it on the advice of a tranny shop mechanic. The noise was there before i replaced it and still remains, what other bearings or part is there that would squeak? Is it internal tranny maybe, i did not rebuild it.



All times are GMT -5. The time now is 04:50 AM.