MustangForums.com
Completed Passenger Door Panel
Completed Passenger Door Panel
0 2020/01/14 15:39:51
Completed Driver Door Panel
Completed Driver Door Panel
0 2020/01/14 15:39:49
0 2020/01/14 15:39:47
0 2020/01/14 15:39:45
0 2020/01/14 15:39:43
0 2020/01/14 15:39:41
0 2020/01/14 15:39:39
Wire ends taped down out of the way
Wire ends taped down out of the way
0 2020/01/14 15:39:37
Wires tied on back side of door panel
Wires tied on back side of door panel
0 2020/01/14 15:39:35
Insert wires being threaded into door panel
Insert wires being threaded into door panel
0 2020/01/14 15:39:34
Finished insert replacement
Finished insert replacement
0 2020/01/14 15:39:32
Vinyl and Masonite sprayed with glue
Vinyl and Masonite sprayed with glue
0 2020/01/14 15:39:30
Masonite glued to new vinyl with border lines showing
Masonite glued to new vinyl with border lines showing
0 2020/01/14 15:39:27
0 2020/01/14 15:39:25
Masonite with three layers of polyester medium-weight batting glued in decreasing sizes
Masonite with three layers of polyester medium-weight batting glued in decreasing sizes
0 2020/01/14 15:39:23
Back side of new vinyl showing transferred border-plus-inch outline from front side
Back side of new vinyl showing transferred border-plus-inch outline from front side
0 2020/01/14 15:39:20
0 2020/01/14 15:39:17
Completed embroidery on new vinyl
Completed embroidery on new vinyl
0 2020/01/14 15:39:15
Back of panel showing wires threaded through hole pairs
Back of panel showing wires threaded through hole pairs
0 2020/01/14 15:39:13
Bell wire sections cut to approximately 14 inches each
Bell wire sections cut to approximately 14 inches each
0 2020/01/14 15:39:10
Showing opened hole through factory door panel insulator pad after drilling
Showing opened hole through factory door panel insulator pad after drilling
0 2020/01/14 15:39:08
Trimming Masonite 'bloom' on back side of panel
Trimming Masonite 'bloom' on back side of panel
0 2020/01/14 15:39:06
Smoothing hole rims with screwdriver handle end
Smoothing hole rims with screwdriver handle end
0 2020/01/14 15:39:03
Drilling complete, Masonite over insert area, cardboard template above it
Drilling complete, Masonite over insert area, cardboard template above it
0 2020/01/14 15:39:01
Drilling complete
Drilling complete
0 2020/01/14 15:38:59
I used extra drill bits to register the location of the Masonite over the door panel insert area
I used extra drill bits to register the location of the Masonite over the door panel insert area
0 2020/01/14 15:38:57
Pay attention to the locating lugs on the back of the door panels
Pay attention to the locating lugs on the back of the door panels
0 2020/01/14 15:38:54
D
D
0 2020/01/14 15:38:52
Embroidery in progress
Embroidery in progress
0 2020/01/14 15:38:50
This glue was good for attaching the vinyl to the foundation panel
This glue was good for attaching the vinyl to the foundation panel
0 2020/01/14 15:38:47
Panel install complete, driver side
Panel install complete, driver side
0 2020/01/14 10:58:54
Wires taped down
Wires taped down
0 2020/01/14 10:58:52
Wires tied off on back of door panel
Wires tied off on back of door panel
0 2020/01/14 10:58:50
Threading wires through door panel
Threading wires through door panel
0 2020/01/14 10:58:48
Finished panel wrapping
Finished panel wrapping
0 2020/01/14 10:58:46
Vinyl and board glued, ready for wrapping
Vinyl and board glued, ready for wrapping
0 2020/01/14 10:58:44
Center of new vinyl glued to padding
Center of new vinyl glued to padding
0 2020/01/14 10:58:42
0 2020/01/14 10:58:40
Masonite panel with three layers of polyester medium-weight batting glued on top in decreasing sizes of 1/4" less for each layer
Masonite panel with three layers of polyester medium-weight batting glued on top in decreasing sizes of 1/4" less for each layer
0 2020/01/14 10:58:38
Dashed line shows transfer of one-inch border line from front of vinyl
Dashed line shows transfer of one-inch border line from front of vinyl
0 2020/01/14 10:58:35