rear driver side wheel sticking out.
#1
rear driver side wheel sticking out.
so i notice when i accelerate that one of my rear tire seems to pick up more grip. i'm not the best driver or anything but i can tell that one of them seems to either spin more or grab more grip. so i went to check them and i notice that the driver side is sticking out more than the passenger side here are the pics. also could this be the cause on my it feels like one side spins more?
here is the driver side
here is the passenger side
here is the driver side
here is the passenger side
Last edited by BlackShelbyGt500; 02-01-2015 at 10:49 PM.
#2
I'f you've lowered it, you need an adjustable panhard bar to re-center the rear end under the car.
I recommend the BMR adjustable panhard bar with poly bushings at each end from AmericanMuscle.com. That will fix you right up!
I recommend the BMR adjustable panhard bar with poly bushings at each end from AmericanMuscle.com. That will fix you right up!
#3
Its called Torque. The motor spins in one direction, as does the transmission (when moving forward), the driveshaft, and the other connected components. The torque is only applied by the motor in one direction. It is the same principle that causes a drag car to lift up and twist off the starting line. The same thing happens in your car to a lesser degree when you step on the gas. The car wants to twist one wheel into the ground and lift up on the other side. Having the solid rear axle in the Mustang embellishes this a little extra too. This has nothing to do with the axle not being centered as your post implies.
Most Mustangs from the factory do not have the axle perfectly centered. If it bothers you, an adjustable panhard bar will allow you to adjust it back to center. I think up to 3/8" off-center is considered perfectly "normal" for these cars.
Most Mustangs from the factory do not have the axle perfectly centered. If it bothers you, an adjustable panhard bar will allow you to adjust it back to center. I think up to 3/8" off-center is considered perfectly "normal" for these cars.
#5
thank bro. would the steeda be better than the BMR? i'm trying to stick to one brand as i already have a steeda cai and pulley.
#6
Its called Torque. The motor spins in one direction, as does the transmission (when moving forward), the driveshaft, and the other connected components. The torque is only applied by the motor in one direction. It is the same principle that causes a drag car to lift up and twist off the starting line. The same thing happens in your car to a lesser degree when you step on the gas. The car wants to twist one wheel into the ground and lift up on the other side. Having the solid rear axle in the Mustang embellishes this a little extra too. This has nothing to do with the axle not being centered as your post implies.
Most Mustangs from the factory do not have the axle perfectly centered. If it bothers you, an adjustable panhard bar will allow you to adjust it back to center. I think up to 3/8" off-center is considered perfectly "normal" for these cars.
Most Mustangs from the factory do not have the axle perfectly centered. If it bothers you, an adjustable panhard bar will allow you to adjust it back to center. I think up to 3/8" off-center is considered perfectly "normal" for these cars.
#7
is there anyway to actually confirm this? how should i go about checking the posi?
#9
Get an on-car adjustable panhard bar if you are lowered. (edit, i just noticed this has a link to amazon PHBs when not signed in, I didnt intend that)
If not lowered, make sure you are on a totally flat surface and, I think there will be some side to side variation depending on how full gas tank is, etc
If not lowered, make sure you are on a totally flat surface and, I think there will be some side to side variation depending on how full gas tank is, etc
Last edited by Andy13186; 02-04-2015 at 02:22 PM.
#10
the Feeling of one tire gripping more is absolutely the torque of the car. these vehicles have crazy amounts of power and will have the car lurching just by reving the motor. the wheel sticking out is caused by the vehicle being lowered. 100% on that.
when you lower the vehicle the whole rear axle assembly is shifted to one side of the car (driver side?) and you need something that re centers it.
looky here!
when you lower the vehicle the whole rear axle assembly is shifted to one side of the car (driver side?) and you need something that re centers it.
looky here!