Going to put stripes on afterall... FINISHED - New pics added
#11
RE: Going to put stripes on afterall... Mock-up
Need some help really quick... Does anyone have any info on removing the pony emblems on the side and re-applying them? Are they bolted on too? Anyone have a writeup for this so I don't have to go digging too far in?
I can get around this while applying the vinyl and work it underneath, but it's going to be a pain. I'd rather strip them first then re-apply with 3m double stick afterwards. Has anyone done this successfully without damaging the emblems?? Perhaps some fishing line and a little heat?
Thanks in advance. I'll put some pics up today of the side decals.
I can get around this while applying the vinyl and work it underneath, but it's going to be a pain. I'd rather strip them first then re-apply with 3m double stick afterwards. Has anyone done this successfully without damaging the emblems?? Perhaps some fishing line and a little heat?
Thanks in advance. I'll put some pics up today of the side decals.
#13
RE: Going to put stripes on afterall... Mock-up
removing my ponies was a huge pain. It took me about 3-4 hours with a blowdryer and some fishing line, then another hour with goo gone to get the adhesive off the car. They're just held on with adhesive and the holes are there for alignment i guess.
#14
RE: Going to put stripes on afterall... Mock-up
At work right now. Ok I guess i'm just going to keep them on there and work around them since. It would take less time and be easier for me than having to strip that all off, re-apply the adhesive and then align it all again.
Thanks guys. I'll show you guys some pics today of the sides if it doesn't get too dark out by the time I leave.
Thanks guys. I'll show you guys some pics today of the sides if it doesn't get too dark out by the time I leave.
#15
RE: Going to put stripes on afterall... Mock-up
Tape off the area around the pony with 3M painters tape trim around emblim with exacto razor (easy stay out of the paint) peel off in one-piece place on stripe and cut out. harder to line up on stripe but might be less time them removing emblims.
#16
RE: Going to put stripes on afterall... Mock-up
LMAO I went ahead and took off the emblems :P
You won't believe how quickly I did it. I was at first going to use the fishing line but instead opted to use a softer vinyl squeegie with my heat gun.
5 minutes each side.
I didn't scrap into it. I kind of wiggled underneath the emblem and then lifted, put the heat gun to flow air under the squeegie and directly to the adhesive. It came off like butter. I dunno if it was a technique I was using or some other odd factor but it was easy as pie.
The sucky part was scraping the crap off the plastic emblems to re-apply them with new double sided automotive tape. Came out CLEAN.
Unfortunately it got too dark out while I was working on it to take good pictures so I will pop a few tomorrow in the afternoon sometime. Came out MUCH better than I anticipated.
EDIT: I used adhesive remover that we use in our shopto take off the gunk that it left behind. Came off pretty easy.
You won't believe how quickly I did it. I was at first going to use the fishing line but instead opted to use a softer vinyl squeegie with my heat gun.
5 minutes each side.
I didn't scrap into it. I kind of wiggled underneath the emblem and then lifted, put the heat gun to flow air under the squeegie and directly to the adhesive. It came off like butter. I dunno if it was a technique I was using or some other odd factor but it was easy as pie.
The sucky part was scraping the crap off the plastic emblems to re-apply them with new double sided automotive tape. Came out CLEAN.
Unfortunately it got too dark out while I was working on it to take good pictures so I will pop a few tomorrow in the afternoon sometime. Came out MUCH better than I anticipated.
EDIT: I used adhesive remover that we use in our shopto take off the gunk that it left behind. Came off pretty easy.