what do u guys think of this motor? HELP!
05-13-2006, 03:24 AM
#1
4th Gear Member
Thread Starter
Join Date: Feb 2006
Location:
Posts: 1,947
what do u guys think of this motor? HELP!
Forged 5.0 Stroker, Hogan's Custom Intake (ready for direct port nitrous), MAC CAI, Crower Cam.590 and .601, Moldex crank, Eagle forged rods, CP Pistons 11:1 compression, 30# Injectrors, Accufab 75mm TB, Billet flywheel, TEA Ported heads 224, 223 cfms, Hooker long tubes, O/R X-pipe, 1 chamber Flowmasters, Univer MA, Pulleys, Caster camber Plts, Sub frame connectors, Steeda ball joints, del alum bushings, Front LCA, Rear U & L Control arms, Vogtland springs, Koni yellow adjustables, 7 qt pan, '03 cobra gas tank. JMS Dyno Tune. Put down 361 RWHP, 333 ft/lbs tq. @ 6500.
this guy in my neighborhood is selling this out of his 2000 GT. just wanted to know could this motor be used in a daily driver. is the cam to extreme for DD? what about the comprission to high for 93 oct?
this guy in my neighborhood is selling this out of his 2000 GT. just wanted to know could this motor be used in a daily driver. is the cam to extreme for DD? what about the comprission to high for 93 oct?
05-13-2006, 04:06 AM
#6
I ♥ Acer
Join Date: May 2006
Location:
Posts: 1,364
RE: what do u guys think of this motor? HELP!
Ya I daily drive some 660 lift motors on the street, 260@50, compression a bit touchy, see what head gasket hes running now and see if you can play wih that to lower CR. Quite frankly though, those HP/TQ numbers look horrible to me, for what has been done to that motor
05-13-2006, 04:08 AM
#7
4th Gear Member
Thread Starter
Join Date: Feb 2006
Location:
Posts: 1,947
RE: what do u guys think of this motor? HELP!
no, i spoken with him a few days ago and we were discussing what he had done to his stang. well way half way jokin when i asked how much he wanted for it. and he replied 3 k with the trans.
05-13-2006, 04:11 AM
#8
4th Gear Member
Thread Starter
Join Date: Feb 2006
Location:
Posts: 1,947
RE: what do u guys think of this motor? HELP!
my 02 gt would be the car its goin into and just wanted to know was the massive cam gonna be a problem to drive daily? and what kind of power do you think he should be making with the modfications he has done.
he only dirves the car on weekends and has never seen rain. this was his project for the past 3 years.
he only dirves the car on weekends and has never seen rain. this was his project for the past 3 years.
05-13-2006, 04:34 AM
#9
2nd Gear Member
Join Date: Jan 2006
Location:
Posts: 174
RE: what do u guys think of this motor? HELP!
Let's see if I got this straight....only driven to church on Sunday, never in the rain, worked on it for 3 years, has a long list of expensive stuff on it, and only wants 3k AND you get the tranny? Yeah, I've put this new engine in my car to putt around and never even plan to get on it, and later I'll give it away for half price to my neighbor. My advice, run like the wind.
05-13-2006, 07:37 AM
#10
3rd Gear Member
Join Date: Dec 2005
Location:
Posts: 533
RE: what do u guys think of this motor? HELP!
ORIGINAL: myshifter
Ya I daily drive some 660 lift motors on the street, 260@50, compression a bit touchy, see what head gasket hes running now and see if you can play wih that to lower CR. Quite frankly though, those HP/TQ numbers look horrible to me, for what has been done to that motor
Ya I daily drive some 660 lift motors on the street, 260@50, compression a bit touchy, see what head gasket hes running now and see if you can play wih that to lower CR. Quite frankly though, those HP/TQ numbers look horrible to me, for what has been done to that motor