460 build thread
Thread Starter
aka 'Negative Nancy'
Joined: Jul 2007
Posts: 4,839
From: Ohio
460 build thread *updated 2/26*
Mod List
Engine
stock 460 block and internals
new bearings/rings
cam/springs/hydraulic lifters
7qt oil pan
stock d3 heads with full super cobra jet port job
weiand scj stealth intake
holley 750 doublepumper w/ trickit ( hopefully switching up to an 850 demon... )
high torque mini starter
200 shot plate kit
Exhaust
hooker super comp ceramic coated LTs
jegs OR x pipe (3")
dynomax bullet mufflers
dumps before rear axle
Ignition
mallory hyfire 6 box
msd dizzy
msd coil
Fuel
Custom sumped tank
holley black pump
aluminum lines
Cooling
undecided...gotta see what we can fit
Brakes
abs delete
upr manual brake setup
Gauges
undecided...the whole pod will need replaced with new trans and no ecu
Front suspension
94/95 stock gt k member
1" k member spacer
GMS 300lb coil overs
flaming river quick ratio manual steering rack
Steeda bump steer kit
4 bolt MM CC plates
Rear suspension
stock for now...might throw some LCAs in
Rear end
Strange 33 spline axles
Strange Spool
LPW Ultimate Girdle
LPW Brace Kit
Rollbar tubing enforced on the front
3.73 gears
Wheels
15x3 jegs stars with sumi skinnies
15x8 (for now) jegs stars with 275/60r15 MT street radials
Exterior
v6 rear bumper
3" cowl
headlight covers
lots of tint
mach 1 lip
debadged
Drivetrain
c6 auto
3200 stall
tci manual valvebody
b&m trans cooler
external filter
b&m bandit shifter
custom length driveshaft
lots of goodies
my buddy got most of the block prep done, just need to hone it,wash,install the cam bearings.
started cleaning the rest up.
starting getting the heads out for cleaning, removed the springs, do some clean up.
thats where we're at now... going to finish cleaning the internals up and get them installed in the block...then im waiting on my oil pan and the bottom end will be finished (after cam install too obviously)
Engine
stock 460 block and internals
new bearings/rings
cam/springs/hydraulic lifters
7qt oil pan
stock d3 heads with full super cobra jet port job
weiand scj stealth intake
holley 750 doublepumper w/ trickit ( hopefully switching up to an 850 demon... )
high torque mini starter
200 shot plate kit
Exhaust
hooker super comp ceramic coated LTs
jegs OR x pipe (3")
dynomax bullet mufflers
dumps before rear axle
Ignition
mallory hyfire 6 box
msd dizzy
msd coil
Fuel
Custom sumped tank
holley black pump
aluminum lines
Cooling
undecided...gotta see what we can fit
Brakes
abs delete
upr manual brake setup
Gauges
undecided...the whole pod will need replaced with new trans and no ecu
Front suspension
94/95 stock gt k member
1" k member spacer
GMS 300lb coil overs
flaming river quick ratio manual steering rack
Steeda bump steer kit
4 bolt MM CC plates
Rear suspension
stock for now...might throw some LCAs in
Rear end
Strange 33 spline axles
Strange Spool
LPW Ultimate Girdle
LPW Brace Kit
Rollbar tubing enforced on the front
3.73 gears
Wheels
15x3 jegs stars with sumi skinnies
15x8 (for now) jegs stars with 275/60r15 MT street radials
Exterior
v6 rear bumper
3" cowl
headlight covers
lots of tint
mach 1 lip
debadged
Drivetrain
c6 auto
3200 stall
tci manual valvebody
b&m trans cooler
external filter
b&m bandit shifter
custom length driveshaft
lots of goodies
my buddy got most of the block prep done, just need to hone it,wash,install the cam bearings.
started cleaning the rest up.
starting getting the heads out for cleaning, removed the springs, do some clean up.
thats where we're at now... going to finish cleaning the internals up and get them installed in the block...then im waiting on my oil pan and the bottom end will be finished (after cam install too obviously)
Last edited by 99BlackPonyGT; May 23, 2009 at 10:48 PM.
Thread Starter
aka 'Negative Nancy'
Joined: Jul 2007
Posts: 4,839
From: Ohio
everything cleaned, my buddy knocked new cam bearing in it
honed, crank checked great, new bearing rings etc!
just waiting on a few dumb parts now
and a idea of what it will look like
we're going to start resealing the heads and do some clean up work on them, and everything on this thing will be going blacked out. only thing shiny will be the bolts.
honed, crank checked great, new bearing rings etc!
just waiting on a few dumb parts now
and a idea of what it will look like
we're going to start resealing the heads and do some clean up work on them, and everything on this thing will be going blacked out. only thing shiny will be the bolts.
