MustangForums.com

Carolina Regional Chapter Chapter President: HT

Boss intake

Thread Tools
 
Search this Thread
 
Old 02-20-2013, 01:17 PM
  #11  
uin2it
3rd Gear Member
 
uin2it's Avatar
 
Join Date: Dec 2008
Location: Goldsboro, NC
Posts: 663
Default
I still see people installing these Intake Manifolds....I thought they were not recommended due to them losing a ton of low end TQ!? SO why are they still being installed!?

Who's tune did you go with!? Too bad you couldnt do before & after dyno runs!
Let us knwo how it feels when you get to drive it!
uin2it is offline  
Reply
Old 02-20-2013, 01:18 PM
  #12  
clowe1965
6th Gear Member
 
clowe1965's Avatar
 
Join Date: Aug 2011
Location: South Carolina, Axle swap anyone?
Posts: 5,287
Default
Did it come with that huge insulation piece that goes underneath the runners? Or you just left that open?
clowe1965 is offline  
Reply
Old 02-20-2013, 02:13 PM
  #13  
alan0614
6th Gear Member
 
alan0614's Avatar
 
Join Date: Jun 2011
Location: North Carolina
Posts: 7,051
Default
OK Harold, how long from start to finish?
alan0614 is offline  
Reply
Old 02-20-2013, 02:40 PM
  #14  
Jeffk
6th Gear Member
 
Jeffk's Avatar
 
Join Date: Aug 2011
Location: Thomasville, NC Where we beat headers into submission!!
Posts: 7,233
Default
Question from the non-5.0 guy. Do you have to get new coil covers now or can you still use the ones that you just had dipped?
Jeffk is offline  
Reply
Old 02-20-2013, 02:53 PM
  #15  
alan0614
6th Gear Member
 
alan0614's Avatar
 
Join Date: Jun 2011
Location: North Carolina
Posts: 7,051
Default
Should be able to use the same ones. I think the Boss covers are just blue.
alan0614 is offline  
Reply
Old 02-20-2013, 03:01 PM
  #16  
hwm3
3rd Gear Member
Thread Starter
 
hwm3's Avatar
 
Join Date: Dec 2006
Location: NC
Posts: 564
Default
Originally Posted by Jeffk
Might skin a knuckle loading that tune...wear protection.
Didn't skin a knuckle, but did get a wicked paper cut.
hwm3 is offline  
Reply
Old 02-20-2013, 03:03 PM
  #17  
Jeffk
6th Gear Member
 
Jeffk's Avatar
 
Join Date: Aug 2011
Location: Thomasville, NC Where we beat headers into submission!!
Posts: 7,233
Default
Originally Posted by hwm3
Didn't skin a knuckle, but did get a wicked paper cut.
Those are the WORST! Hopefully you were able to push through the pain and complete the task though.
Jeffk is offline  
Reply
Old 02-20-2013, 03:05 PM
  #18  
hwm3
3rd Gear Member
Thread Starter
 
hwm3's Avatar
 
Join Date: Dec 2006
Location: NC
Posts: 564
Default
Originally Posted by clowe1965
Did it come with that huge insulation piece that goes underneath the runners? Or you just left that open?
No insulation under the runners. Might get the side covers to clean it up a bit under there.
hwm3 is offline  
Reply
Old 02-20-2013, 03:07 PM
  #19  
hwm3
3rd Gear Member
Thread Starter
 
hwm3's Avatar
 
Join Date: Dec 2006
Location: NC
Posts: 564
Default
Originally Posted by alan0614
OK Harold, how long from start to finish?
I'd say 3 hours including downloading the new tunes and uploading to the car. It's really not a bad job.
hwm3 is offline  
Reply
Old 02-20-2013, 03:07 PM
  #20  
hwm3
3rd Gear Member
Thread Starter
 
hwm3's Avatar
 
Join Date: Dec 2006
Location: NC
Posts: 564
Default
Originally Posted by alan0614
Should be able to use the same ones. I think the Boss covers are just blue.
Yeah.
hwm3 is offline  
Reply



Advanced Search
Quick Reply: Boss intake


Reply Closed Thread Share
Forum Jump

All times are GMT -5. The time now is 06:07 AM.