427 shortblock NEW, C4 1110HP and parts, SN 95 351 headers
#1
427 shortblock NEW, C4 1110HP and parts, SN 95 351 headers
Bunch of parts for sale. Best way to to contact me is through PM. Only reason i am selling any of these parts is i am selling the car. Cant afford to finish it. Rather not ship motor and trans.
1974 351w block cleaned, bored and honed with torque plates to 4.040 decked to 9.467"
new cam bearings installed and line hone was checked and good.
Probe dominator rotating assembly ballanced to 28oz
4340 forged 4.17" stroke crankshaft with 2.1" rod journals.
6.2" Probe lighweight 4340 rods with ARP 2000 rod bolt upgrade
Probe 2618 forged 4.040 bore 1.175CH flat-top pistons with tool-steel wrist pin upgrade.
Perfect Circle file-fit 1/16 1/16 3.0mm rings gapped to .022 top, .028 second. Clevite H-series rod and main bearings .0025 clearance on rod journals and .003 on mains.
The block was clearanced for the stroker and cam/rod clearance was checked.
The motor was assembled with ARP main studs and Permatex assembly lube on the bearings/wrist pins.
Would cost you over 3500 to build this. I will also throw in a new HV oil pump, pick up tube, and oil pan.
I would like to get 2400
http://img.photobucket.com/albums/v3...Zealot/427.jpg
http://img.photobucket.com/albums/v3...lot/bottom.jpg
http://img.photobucket.com/albums/v3...lot/oilpan.jpg
http://img.photobucket.com/albums/v3...pumppickup.jpg
I HAVE A MANUAL VALVE BODY W/T-BRAKE,FULLY ROLLERIZED MIGHTY MIGHT M2 C-4. TRANS IS 1100HP CAPABLE. Has 700 street miles. Trans alone was 1800. I would like 1200
used but in great condition JW 8" converter for a small block ford. It has a 10.5" bolt pattern, It stalled about 5400-5500 behind a 347 stroker on the brake. This converter is well over $800 new. Would like350
used C4 trans cooler with braided lines and fittings they are all put together and ready to install braided lines are correct length from trans fluid output to front of radiator.cooler has fittings also. Cost about 180 to make this. Would like to get 120
Used FMS aluminum driveshaft. Would like to get 150
Also got a 28 oz flexplate for this setup. Would like to get 40.
Somebody could take All drivetrain for 1700. Just need shifter.
headers are to put a 351 in an SN 95 chassis. 1 7/8 primaries3 inch collectorsUsed but in great shape. Cost 1020 from kooks. I would like to get 500
1974 351w block cleaned, bored and honed with torque plates to 4.040 decked to 9.467"
new cam bearings installed and line hone was checked and good.
Probe dominator rotating assembly ballanced to 28oz
4340 forged 4.17" stroke crankshaft with 2.1" rod journals.
6.2" Probe lighweight 4340 rods with ARP 2000 rod bolt upgrade
Probe 2618 forged 4.040 bore 1.175CH flat-top pistons with tool-steel wrist pin upgrade.
Perfect Circle file-fit 1/16 1/16 3.0mm rings gapped to .022 top, .028 second. Clevite H-series rod and main bearings .0025 clearance on rod journals and .003 on mains.
The block was clearanced for the stroker and cam/rod clearance was checked.
The motor was assembled with ARP main studs and Permatex assembly lube on the bearings/wrist pins.
Would cost you over 3500 to build this. I will also throw in a new HV oil pump, pick up tube, and oil pan.
I would like to get 2400
http://img.photobucket.com/albums/v3...Zealot/427.jpg
http://img.photobucket.com/albums/v3...lot/bottom.jpg
http://img.photobucket.com/albums/v3...lot/oilpan.jpg
http://img.photobucket.com/albums/v3...pumppickup.jpg
I HAVE A MANUAL VALVE BODY W/T-BRAKE,FULLY ROLLERIZED MIGHTY MIGHT M2 C-4. TRANS IS 1100HP CAPABLE. Has 700 street miles. Trans alone was 1800. I would like 1200
used but in great condition JW 8" converter for a small block ford. It has a 10.5" bolt pattern, It stalled about 5400-5500 behind a 347 stroker on the brake. This converter is well over $800 new. Would like350
used C4 trans cooler with braided lines and fittings they are all put together and ready to install braided lines are correct length from trans fluid output to front of radiator.cooler has fittings also. Cost about 180 to make this. Would like to get 120
Used FMS aluminum driveshaft. Would like to get 150
Also got a 28 oz flexplate for this setup. Would like to get 40.
Somebody could take All drivetrain for 1700. Just need shifter.
headers are to put a 351 in an SN 95 chassis. 1 7/8 primaries3 inch collectorsUsed but in great shape. Cost 1020 from kooks. I would like to get 500
Thread
Thread Starter
Forum
Replies
Last Post
asdiu
Parts For Sale
1
08-26-2006 07:44 PM
87mustang347
Parts For Sale
0
12-09-2005 04:46 PM