Jack Points 03 Cobra
3rd Gear Member
Joined: Dec 2004
Posts: 526
From:
RE: Jack Points 03 Cobra
Get some full lengths welded in, they make excellent jacking points...
Otherwise...you can use the spot where the factory jack goes or use a piece of wood and hit the spot where the full lengths would get welded two.
Otherwise...you can use the spot where the factory jack goes or use a piece of wood and hit the spot where the full lengths would get welded two.
5th Gear Member
Joined: Apr 2006
Posts: 3,625
RE: Jack Points 03 Cobra
ORIGINAL: ModularMax
full length sub-frame connectors?
full length sub-frame connectors?
Heck, I even have to lift my car a little to get under the pinch weld. 1.5" up front and .75" out back?????There is a spot in the back on the gt's not sure bout cobras w/ irs. It's about 5 or so inches past the weld going into the car just infront of the tire. That's a solid firm lift point!
3rd Gear Member
Joined: Dec 2004
Posts: 526
From:
RE: Jack Points 03 Cobra
ORIGINAL: 97targa
LOL..yeah right, like I can put a jack even under the frame without the connectors! Get a piece of 1" boxed steel and have it welded on the inside of the pinch weld. Works great for me...Thanks Kenny Brown Heck, I even have to lift my car a little to get under the pinch weld. 1.5" up front and .75" out back?????
There is a spot in the back on the gt's not sure bout cobras w/ irs. It's about 5 or so inches past the weld going into the car just infront of the tire. That's a solid firm lift point!
ORIGINAL: ModularMax
full length sub-frame connectors?
full length sub-frame connectors?
Heck, I even have to lift my car a little to get under the pinch weld. 1.5" up front and .75" out back?????There is a spot in the back on the gt's not sure bout cobras w/ irs. It's about 5 or so inches past the weld going into the car just infront of the tire. That's a solid firm lift point!
1st Gear Member
Joined: Aug 2007
Posts: 98
From: Bayside, NY
RE: Jack Points 03 Cobra
Go to Sears buy a craftsman floor jack and your done. True story; I was in hershey pa, and got a flat on my Navigator, had to lift that sucker with the jack from the factory, ohh and without any specific jack points. Had to lift her on the automated running boards and i lived to tell you this story and the truck is fine too, soothe cobra will be fine
5th Gear Member
Joined: Sep 2006
Posts: 2,966
From: Raleigh, NC
RE: Jack Points 03 Cobra
ORIGINAL: AllVenom
Most 03/04 Cobra owners don't lower their car so the jacks they make for low clearances work fine. And yes, I meant full length sub frame connectors. I got the Maximum Motorsport ones. Very nice.
ORIGINAL: 97targa
LOL..yeah right, like I can put a jack even under the frame without the connectors! Get a piece of 1" boxed steel and have it welded on the inside of the pinch weld. Works great for me...Thanks Kenny Brown Heck, I even have to lift my car a little to get under the pinch weld. 1.5" up front and .75" out back?????
There is a spot in the back on the gt's not sure bout cobras w/ irs. It's about 5 or so inches past the weld going into the car just infront of the tire. That's a solid firm lift point!
ORIGINAL: ModularMax
full length sub-frame connectors?
full length sub-frame connectors?
Heck, I even have to lift my car a little to get under the pinch weld. 1.5" up front and .75" out back?????There is a spot in the back on the gt's not sure bout cobras w/ irs. It's about 5 or so inches past the weld going into the car just infront of the tire. That's a solid firm lift point!
Thread
Thread Starter
Forum
Replies
Last Post
jwog666
Pipes, Boost & Juice
11
Dec 27, 2021 08:09 PM
MustangForums Editor
Mustang News, Concepts, Rumors & Discussion
0
Sep 25, 2015 09:06 AM
