took apart the T5 tonight. some pictures
#1
took apart the T5 tonight. some pictures
so, taking apart the T5 really wasnt as complicted as i thought it would be. I pulled most of it apart with minimal tools, no press. and a couple blocks of wood. I still have about half of the main shaft to do, but i have to stop by a machine shop to get it pressed apart (da#n[:@]was hoping to do this all myself! hah), and get the cases cleaned in a fancy wachingmachine.
heres some pictures if anyonewants a look. nothing special
http://i238.photobucket.com/albums/f...Picture026.jpg
http://i238.photobucket.com/albums/f...Picture028.jpg
That rear seal sure was a B#$ch! messed it up a little
http://i238.photobucket.com/albums/f...Picture022.jpg
http://i238.photobucket.com/albums/f...Picture029.jpg
nice emty case.
heres some pictures if anyonewants a look. nothing special
http://i238.photobucket.com/albums/f...Picture026.jpg
http://i238.photobucket.com/albums/f...Picture028.jpg
That rear seal sure was a B#$ch! messed it up a little
http://i238.photobucket.com/albums/f...Picture022.jpg
http://i238.photobucket.com/albums/f...Picture029.jpg
nice emty case.
#5
RE: took apart the T5 tonight. some pictures
Where did you end up getting the rebuild parts and replacement gears? Also did you get a one piece steel retainer and the improved counter gear retainer? Also which videos did you get? I already had the cartapes.com video I was telling you about but I also recently bought the badshoe video and it is really good too.
#6
RE: took apart the T5 tonight. some pictures
yeah, it was fun. im happy with the synchroscondition aswell. all nice and sharp. I Got cluster and 1-4 gears on ebay. havnt yet got the steel retainers. ill proably go through rose hill. I emailed them, and they were good.
as for video, i got the hanlon one (car tapes). its good. moves fast.
press from harbor freight...havnt seen one, but im going over there this afternoon anyway
thanks for all the help so far!
as for video, i got the hanlon one (car tapes). its good. moves fast.
press from harbor freight...havnt seen one, but im going over there this afternoon anyway
thanks for all the help so far!
#7
RE: took apart the T5 tonight. some pictures
Overhauling a transmission is a major project and not something you want to have to redo so if it was me I would replace the blocking rings and sincroes and of course all the bearings. Not replacing the sincroes and blocker rings is kind of like putting in a new clutch and not replacing the pilot or throw out bearings, you can use the old parts but if they arn't up to the task you have to pull it all back out and do it again. Just my opinion
#8
RE: took apart the T5 tonight. some pictures
ORIGINAL: flyingfool
yeah, it was fun. im happy with the synchroscondition aswell. all nice and sharp. I Got cluster and 1-4 gears on ebay. havnt yet got the steel retainers. ill proably go through rose hill. I emailed them, and they were good.
as for video, i got the hanlon one (car tapes). its good. moves fast.
press from harbor freight...havnt seen one, but im going over there this afternoon anyway
thanks for all the help so far!
yeah, it was fun. im happy with the synchroscondition aswell. all nice and sharp. I Got cluster and 1-4 gears on ebay. havnt yet got the steel retainers. ill proably go through rose hill. I emailed them, and they were good.
as for video, i got the hanlon one (car tapes). its good. moves fast.
press from harbor freight...havnt seen one, but im going over there this afternoon anyway
thanks for all the help so far!
Thread
Thread Starter
Forum
Replies
Last Post
daltron
5.0L GT S550 Tech
17
04-28-2016 08:10 PM
treesloth
New Member Area
4
09-28-2015 07:03 AM