Casper help!!!!g
Thread Starter
2nd Gear Member
Joined: Feb 2005
Posts: 345
From:
Casper help!!!!g
sigh.... this is the worst night of my life. I was going with my friends up to ennis texas for his b-day and we all went to the drive in movie. on the way up there I was following a friend in a four runner suv. they ran over a tire as we were entering the exit ramp. it floated like a trash bag and before I knew it I ran over it. I was a good 4 or 5 car links behind them. anyways I got to looking at my car and the right side of the front bumber is screwed. the black plastic part in the lower grill area that is close to the ground is almost ripped off. and the plastice which is painted the same as the car is behind that and it is bent inward badly.
will I have to replace the whole front area? (from below the lights and down)
do you know about how much that would cost.
thanks
gotta go to dealership tommara to get it looked at.
will I have to replace the whole front area? (from below the lights and down)
do you know about how much that would cost.
thanks
gotta go to dealership tommara to get it looked at.
2nd Gear Member
Joined: Feb 2005
Posts: 233
From:
RE: Casper help!!!!g
sucks bro... well this might be a good excuse to get a lower splitter if you want to change the stock look so it dosen't look like every one else's mineral grey GT. sorry to read that about your stang
. hope she feels better in a few days.
. hope she feels better in a few days.
ORIGINAL: V8 Aggie
sigh.... this is the worst night of my life. I was going with my friends up to ennis texas for his b-day and we all went to the drive in movie. on the way up there I was following a friend in a four runner suv. they ran over a tire as we were entering the exit ramp. it floated like a trash bag and before I knew it I ran over it. I was a good 4 or 5 car links behind them. anyways I got to looking at my car and the right side of the front bumber is screwed. the black plastic part in the lower grill area that is close to the ground is almost ripped off. and the plastice which is painted the same as the car is behind that and it is bent inward badly.
will I have to replace the whole front area? (from below the lights and down)
do you know about how much that would cost.
thanks
gotta go to dealership tommara to get it looked at.
sigh.... this is the worst night of my life. I was going with my friends up to ennis texas for his b-day and we all went to the drive in movie. on the way up there I was following a friend in a four runner suv. they ran over a tire as we were entering the exit ramp. it floated like a trash bag and before I knew it I ran over it. I was a good 4 or 5 car links behind them. anyways I got to looking at my car and the right side of the front bumber is screwed. the black plastic part in the lower grill area that is close to the ground is almost ripped off. and the plastice which is painted the same as the car is behind that and it is bent inward badly.
will I have to replace the whole front area? (from below the lights and down)
do you know about how much that would cost.
thanks
gotta go to dealership tommara to get it looked at.
Thread Starter
2nd Gear Member
Joined: Feb 2005
Posts: 345
From:
RE: Casper help!!!!g
yea thanks. well I went to ford and they gave me a price of about 585$. that is the whole new front fascia. plus that is without install and I gotta get it painted! rawr!!!!!!
that lower splitter is just part of the fascia and not the whole thing right?
that lower splitter is just part of the fascia and not the whole thing right?
I ♥ Acer
Joined: Mar 2004
Posts: 2,287
From:
RE: Casper help!!!!g
Well, you could heat up the bumper with a blow dryer and bend the bump back out. I have done it plenty of times at my dealership. But i would take it to the dealership just to get it checked out. GEte some prices and what not. sorry to hear..... I wont follow anyone more than like 300 ft. lol. Then again people usually squeeze between us and i dont see them anymore. lol. Then i just wait for a break in the road and down shift and catch up. But yeah thats all i can advise you on.
Thread
Thread Starter
Forum
Replies
Last Post