Too much power
#12
RE: Too much power
Hey,
Actually the kit is listed as a 6psi kit, will make about 34% gain. This is one of the cheapest kits out there. For me this is good because with my P&Pd' heads and bigger cams, any more psi would put in the 400+ range and I don't want that. 350-380 rear wheel and It'll be a mighty fine day [8D]
Actually the kit is listed as a 6psi kit, will make about 34% gain. This is one of the cheapest kits out there. For me this is good because with my P&Pd' heads and bigger cams, any more psi would put in the 400+ range and I don't want that. 350-380 rear wheel and It'll be a mighty fine day [8D]
ORIGINAL: mikev08826
"except you get to hang out with your working friends."
LMAO
You wouldn't want to make 6psi. I'd imagine the charger comes with the 8 psi pulley stock, idk.
As a reference point I'm making 352 rwhp on an otherwise bone stock mustang. Mods in my sig.
ORIGINAL: Armydad
Hey,
I'm looking at a Novi 1000 from THR, how do you like it ? I have a 98 GT, I'll have ported pi heads comp cams, exhaust. I was hoping for 350-380whp with the Novi @ 6psi. Do you think I'll make it. Also your running 7-8 psi, are you intercooled?
Sorry to kinda jack your thread, but doesn't seem to be alot of Novis around
Thanks
Hey,
I'm looking at a Novi 1000 from THR, how do you like it ? I have a 98 GT, I'll have ported pi heads comp cams, exhaust. I was hoping for 350-380whp with the Novi @ 6psi. Do you think I'll make it. Also your running 7-8 psi, are you intercooled?
Sorry to kinda jack your thread, but doesn't seem to be alot of Novis around
Thanks
ORIGINAL: 1BadSonicBlue02GT
Ok i have i a paxton novi 1000, long tube headers, o/r x-pipe, flows, gears, diablo tuned(dynoed), nittos. And thats all, what kind of mods can i do power wise while running stock internals? how far can i push it I'm at 375 rwhp right now. also what would be good suspension mods. I'm all stock in that area.
Ok i have i a paxton novi 1000, long tube headers, o/r x-pipe, flows, gears, diablo tuned(dynoed), nittos. And thats all, what kind of mods can i do power wise while running stock internals? how far can i push it I'm at 375 rwhp right now. also what would be good suspension mods. I'm all stock in that area.
LMAO
You wouldn't want to make 6psi. I'd imagine the charger comes with the 8 psi pulley stock, idk.
As a reference point I'm making 352 rwhp on an otherwise bone stock mustang. Mods in my sig.
#13
RE: Too much power
ORIGINAL: 1BadSonicBlue02GT
Ok i have i a paxton novi 1000, long tube headers, o/r x-pipe, flows, gears, diablo tuned(dynoed), nittos. And thats all, what kind of mods can i do power wise while running stock internals? how far can i push it I'm at 375 rwhp right now. also what would be good suspension mods. I'm all stock in that area.
Ok i have i a paxton novi 1000, long tube headers, o/r x-pipe, flows, gears, diablo tuned(dynoed), nittos. And thats all, what kind of mods can i do power wise while running stock internals? how far can i push it I'm at 375 rwhp right now. also what would be good suspension mods. I'm all stock in that area.
Then you could install a DIY intercooler kit and/or a set of camshafts. With either(and theabove mods)you should be able to make at least 420 WHP safely on a 93 octane tune.
Thread
Thread Starter
Forum
Replies
Last Post
jwog666
Pipes, Boost & Juice
11
12-27-2021 08:09 PM
KingRando
2005-2014 Mustangs
5
10-02-2015 08:06 AM
MustangForums Editor
General Tech
0
09-25-2015 06:58 PM